Ligne 45 : |
Ligne 45 : |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-17.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-17.jpg}} |
− | {{asm-text}} prenez un autre morceau de gaine thermorétractable et enfiler le sur l'autre fil du bloc pile (que vous aurez raccourcis a hauteur de la diode)... | + | {{asm-text}} faite glisser le morceau de gaine rétractable au dessus de la diode... |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-18.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-18.jpg}} |
− | {{asm-text}} …and slide it back over the diode and the solder joints. | + | {{asm-text}} ...et assurez-vous de bien couvrir les deux soudures. |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-19.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-19.jpg}} |
− | {{asm-text}} Shrink the tubing to grip the diode and wires. You can use a heat gun, lighter or the edge of your soldering iron. | + | {{asm-text}} Faire rétrécir la gaine thermo-rétractable sur la diode et les fil. Vous pouvez utiliser un seèche cheveux mais cela fonctionne également avec un briquet ou la partie chauffante du fer à souder. |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-20.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-20.jpg}} |
− | {{asm-text}} Taa-daah! | + | {{asm-text}} Voila, c'est fait! |
| | | |
| {{asm-end}} | | {{asm-end}} |
| | | |
− | The black wire from the battery holder then connects to the ground wire of the LED circuit (or plug/receptacle, if you’ve installed one). This side is much simpler than the diode-equipped wire:
| + | |
| + | Le fil noir de bloc pile est alors soudé connecté sur le fil de masse/gnd dur circuit LED (ou la pole négatif/gnd/masse de votre connecteur, si vous en avez installé une). Ce côté est plus facile à réaliser que le fil avec la diode: |
| | | |
| {{asm-begin}} | | {{asm-begin}} |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-30.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-30.jpg}} |
− | {{asm-text}} Slide a small 1" piece of heat shrink onto the black wire (this image shows a much shorter piece…oops…go a little longer than this). | + | {{asm-text}} Faite glisser une section de 2-3cm de gaine thermorétractable sur le fil noir (n'hésitez pas à utiliser une section plus longue que sur l'image. |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-31.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-31.jpg}} |
− | {{asm-text}} Solder together the ends of the wires. The dreaded inline splice! | + | {{asm-text}} Soudez les deux fils ensembles... bien aligné! |
| | | |
| {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-32.jpg}} | | {{asm-row|img=Alim-Pixel-Accu-Pile-Diode-32.jpg}} |
− | {{asm-text}} Then slide and shrink as you did before. Done! | + | {{asm-text}} Ensuite, faites glisser la gaine thermorétractable comme vous l'avez fait avant. Voila, il ne reste plus qu'à la faire rétrécir et c'est prêt! |
| | | |
| {{asm-end}} | | {{asm-end}} |
| | | |
| {{Alim-Pixel-Accu-Pile-TRAILER}} | | {{Alim-Pixel-Accu-Pile-TRAILER}} |