Ligne 1 : |
Ligne 1 : |
| {{Bluefruit-LE-Shield-NAV}} | | {{Bluefruit-LE-Shield-NAV}} |
− |
| |
− | {{traduction}}
| |
| | | |
| == Le croquis UriBeacon == | | == Le croquis UriBeacon == |
− | The '''UriBeacon''' example shows you how to use the built-in UriBeacon AT commands to configure the Bluefruit LE module as a UriBeacon advertiser, following Google's Physical Web [https://github.com/google/uribeacon UriBeacon] specification.
| + | L'exemple '''UriBeacon''' montre comment utiliser les AT UriBeacon du module pour configurer le module Bluefruit LE comme annonceur UriBeacon en suivant les spécifications [https://github.com/google/uribeacon UriBeacon] de Google. |
| | | |
| == Ouvrir le croquis == | | == Ouvrir le croquis == |
Ligne 18 : |
Ligne 16 : |
| | | |
| == Configuration == | | == Configuration == |
− | Check the '''Configuration!''' page earlier to set up the sketch for Software/Hardware UART or Software/Hardware SPI. The default is hardware SPI
| + | Vérifiez la page '''Configuration''' présenter plus tôt dans le tutoriel! Il est important de configurer le croquis pour utiliser soit l'UART Logiciel/Matériel, soit le bus SPI Logiciel/Matériel correspondant à votre plateforme. Par défaut, le croquis utilise le bus SPI matériel |
| | | |
− | If using software or hardware Serial UART:
| + | Si vous utilisez le port série/UART logiciel ou matériel: |
− | * This tutorial does not need to use the MODE pin, '''make sure you have the mode switch in CMD mode''' if you do not configure & connect a MODE pin | + | * Ce tutoriel ne requière pas l'utilisation de la broche MODE, '''assurez-vous d'avoir l'interrupteur en position CMD''' si vous ne configurer pas (et ne connectez pas) la broche MODE. |
− | * Don't forget to also '''connect the CTS pin on the Bluefruit to ground if you are not using it!''' (The Flora has this already done) | + | * N'oubliez pas de '''connecter la broche CTS sur la masse/GND du Bluefruit si vous n'utilisez pas le signal CTS!''' (Le Flora l'a déjà branché à la masse) |
| | | |
| == Exécuter le croquis == | | == Exécuter le croquis == |
− | Once you upload the sketch to your board (via the arrow-shaped upload icon), and the upload process has finished, open up the Serial Monitor via '''Tools > Serial Monitor''', and make sure that the baud rate in the lower right-hand corner is set to '''115200''':
| + | Une fois le croquis téléversé sur votre carte Arduino, vous pouvez ouvrir le moniteur série via le menu '''Outils > Moniteur série'''. Assurez-vous que le débit (Baud rate) soit configuré sur '''115200''' bauds (en bas à droite): |
| | | |
| {{ADFImage|Bluefruit-LE-Shield-UriBeacon-10.png}} | | {{ADFImage|Bluefruit-LE-Shield-UriBeacon-10.png}} |
| | | |
− | At this point you can open the Physical Web Application for [https://play.google.com/store/apps/details?id=physical_web.org.physicalweb Android] or for [https://itunes.apple.com/us/app/physical-web/id927653608?mt=8 iOS], and you should see a link advertising Adafruit's website:
| + | C'est le moment d'ouvrir un l'application "Physical Web" pour [https://play.google.com/store/apps/details?id=physical_web.org.physicalweb Android] ou pour [https://itunes.apple.com/us/app/physical-web/id927653608?mt=8 iOS] et de voir le lien envoyé pour le liste web d'Adafruit: |
| | | |
| {{ADFImage|Bluefruit-LE-Shield-UriBeacon-20.jpg}} | | {{ADFImage|Bluefruit-LE-Shield-UriBeacon-20.jpg}} |
| | | |
| {{Bluefruit-LE-Shield-TRAILER}} | | {{Bluefruit-LE-Shield-TRAILER}} |