Ligne 10 : |
Ligne 10 : |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-00.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-00.jpg}} |
− | {{asm-text}} Le backpack est livré avvec une section de pinHeader que<br />vous pouvez utiliser pour y fixer l'afficheur.<br />Utiliser un breadboard sera utile pour<br />maintenir le pinHeader<br />bien droit. Votre kit peut également contenir un potentiomètre<br />bleu à 3 broches. Cet élément n'est pas<br />nécessaire, vous pouvez donc le recycler dans<br />vos autres projets. | + | {{asm-text}} Le backpack est livré avec une section de pinHeader que<br />vous pouvez utiliser pour y fixer l'afficheur.<br />Utiliser un breadboard sera utile pour<br />maintenir le pinHeader<br />bien droit. Votre kit peut également contenir un potentiomètre<br />bleu à 3 broches. Cet élément n'est pas<br />nécessaire, vous pouvez donc le recycler dans<br />vos autres projets. |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-01.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-01.jpg}} |
− | {{asm-text}} Break off the header so that it matches the number of pins on your LCD. | + | {{asm-text}} Brisez le pinHeader de façon à avoir le nombre de broche correspondant à votre afficheur LCD. |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-02.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-02.jpg}} |
− | {{asm-text}} Place the header with the long side down into a breadboard. then place the LCD on top. If you're using an LCD with two rows available, make sure you're using the row that matches the image below. | + | {{asm-text}} Enfoncez le pinHeader avec la longue partie dans le breadboard. Seul les petites partie du pinHeader doit être visible, placez y l'afficheur LCD (chaque trou de l'afficheur doit être remplit avec le connecteur). Si vous avez un afficheur avec deux rangée de connecteurs, faite attention à bien utilisé le connecteur comme sur l'image d'ici à côté. |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-03a.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-03a.jpg}} |
| {{asm-img|img=LCD-USB-TTL-Asm-03b.jpg}} | | {{asm-img|img=LCD-USB-TTL-Asm-03b.jpg}} |
− | {{asm-text}} Solder all the headers on with your iron. | + | {{asm-text}} Soudez toutes les broches à l'aide de votre fer à souder. |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-03.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-03.jpg}} |
− | {{asm-text}} Next, align the backpack so that it matches up with the corner of the LCD, the hole in the backpack should be in the same location. | + | {{asm-text}} Ensuite, alignez le backpack de façon à ce qu'il correspond au coin de l'afficheur LCD. Le trou du backpack (en haut à droite) doit correspondre au trou du LCD. |
| | | |
| {{asm-row|img=LCD-USB-TTL-Asm-04.jpg}} | | {{asm-row|img=LCD-USB-TTL-Asm-04.jpg}} |
− | {{asm-text}} Solder the backpack on completely. | + | {{asm-text}} Soudez toutes les broches du backpack. |
| {{asm-end}} | | {{asm-end}} |
| | | |