Ligne 13 : |
Ligne 13 : |
| [[Fichier:PYBD-Butterfly-schema.jpg|800px]] | | [[Fichier:PYBD-Butterfly-schema.jpg|800px]] |
| | | |
− | == Assembler == | + | == Assembly == |
| | | |
| {{asm-begin}} | | {{asm-begin}} |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-02.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-02.jpg|size=480px}} |
− | {{asm-text}} Placer le connecteur JST-PH (Qwiic/StemmaQT) sur l'un des emplacements au verso de la carte. | + | {{asm-text}} Place the JST-PH (Qwiic/StemmaQT) connector on one of the both dedicated site (on the bask of the board). |
| | | |
| + | The both position are wired in parallele on the same I2C bus (so any position are right). |
| | | |
− | Comme il est petit et plus difficile à souder, nous allons commencer par les broches de connexion.
| + | As this connector is quite small and more difficult to solder, we will start with its connexion pin. |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-01.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-01.jpg|size=480px}} |
− | {{asm-text}} Placer un peu de flux sur la carte derrière les broches à souder. Cela aidera l'étain à mouiller les broches. | + | {{asm-text}} Put some flux on the board behind de pins. This will help the stain to melt on the pins and the pad. |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-03.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-03.jpg|size=480px}} |
− | {{asm-text}} Maintenir le connecteur en place pour éviter qu'il bouge durant la soudure des broches. | + | {{asm-text}} Maintain the ronnector right in place while soldering the pins. |
| | | |
| + | As the connector is small, the best is to use a tweezers and apply some pressure to avoid the connector to move. |
| | | |
− | Comme le connecteur est petit, le mieux est encore d'utiliser une pince permettant de presser légèrement le connecteur pour qu'il reste bien en place.
| + | Put some solder on the tip of the iron and put it on the pins. Thanks to the flux, the solder will automagically melt quickly on the pads. |
| | | |
| | | |
− | Charger la pointe du fer avec de l'étain puis venir le déposer sur les broches. Grâce au flux, l'étain mouille les broches et les pastilles. La soudure est quasi instantanée.
| + | '''Next''', just make a solder joint on the fixation pads on the front of the connector (near of the board edge). |
− | | |
− | | |
− | '''Après avoir soudé les broches à l'arrière''', poser un point de soudure sur les deux pattes de fixation situés à chaque les coins avants du connecteur.
| |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-04.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-04.jpg|size=480px}} |
− | {{asm-text}} Positionner le connecteur Grove, le maintenir en place avec vos doigts. Comme il est plus gros, il est plus facile à positionner et maintenir en place. '''Cette opération est relativement facile''''. | + | {{asm-text}} '''Solder the Grove connector is more easy'''. Place the Grove connector and maintain it right in place with your fingers (this connector is bigger enough). |
| | | |
| | | |
− | Charger la pointe du fer à souder avec un de l'étain et venir mouiller les broches du connecteur.
| + | Load the iron tip with some solder and drop off the solder on the connexion pin first (solder should easily melt down on the pads and the pins). |
| | | |
| + | Once the pin soldered, secure the Grove connector in place by applying solder on the sides of the connector. |
| | | |
− | Une fois les broches soudées, fixer les deux côtés du connecteur Grove sur la carte en employant le même procéder.
| + | Repeat the same operations for the second Grove connector. |
− | | |
− | | |
− | Répéter l'opération avec le deuxième connecteur Grove.
| |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-10.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-10.jpg|size=480px}} |
− | {{asm-text}} Saisir la rangée de connecteur mâle et la sectionner en 4 connecteurs de 8 broches et un connecteur de 3 broches. | + | {{asm-text}} Pick up the male connector and split it in 4 sections of 8 pins and 1 section of 3 pins. |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-11.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-11.jpg|size=480px}} |
− | {{asm-text}} Une fois les connecteurs soudés, la carte doit ressembler à ceci. | + | {{asm-text}} Once the connectors soldered, the board should look like to this picture. |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-20.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-20.jpg|size=480px}} |
− | {{asm-text}} Préparer et souder les connecteurs femelle 1x3 utilisés pour les points de masse. | + | {{asm-text}} Pick the 1x3 female connectors and solder them on the board. |
− | | |
− | Souder les connecteurs sur la carte.
| |
| | | |
| {{asm-row|img=PYBD-Butterfly-asm-21.jpg|size=480px}} | | {{asm-row|img=PYBD-Butterfly-asm-21.jpg|size=480px}} |