30 072
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
RASP-SENSE-HAT-ASTRO-PI-Assembler (voir la source)
Version du 24 août 2015 à 19:47
, 24 août 2015 à 19:47Page créée avec « {{RASP-SENSE-HAT-ASTRO-PI-NAV}} == Monter le Sense Hat == '''1.''' If you have not yet installed the Sense HAT, now is the time to do so. Do this with the Raspberry Pi shut ... »
{{RASP-SENSE-HAT-ASTRO-PI-NAV}}
== Monter le Sense Hat ==
'''1.''' If you have not yet installed the Sense HAT, now is the time to do so. Do this with the Raspberry Pi shut down, disconnected from the mains, and with all other cables disconnected.
'''2.''' The Sense HAT comes in a silver anti-static bag, along with the following fixtures and fittings:<br />Check that these are all present before proceeding.
* 1 x GPIO pin extension header
* 4 x Hexagon stand-offs (female-to-female)
* 8 x M2.5 screws
'''3.''' This diagram shows how it all fits together.
[[Fichier:RASP-SENSE-HAT-ASTRO-PI-10.png]]
'''4.''' First, put the GPIO extension header block onto the Raspberry Pi GPIO pins.
'''5.''' Screw the hexagon stand-offs to the Raspberry Pi itself, by threading the screws through from the bottom and turning the hexagon stand-offs between finger and thumb.
'''6.''' Next, insert the Sense HAT into the GPIO pin extension header. The corner holes should line up with the hexagon stand-offs.
'''7.''' Lastly, put the remaining screws through from the top.
'''8.''' Use a small Phillips screwdriver to tighten each corner stand-off individually. They don't need to be especially tight, just enough to ensure that the HAT doesn't become loose.
== Ensuite ==
Maintenant que nous avons tout assembler et que le Sense HAT est branché sur votre Raspberry-Pi, nous allons avoir besoin de [[RASP-SENSE-HAT-ASTRO-PI-Logiciel|procéder à l'installation du logiciel]].
{{RASP-SENSE-HAT-ASTRO-PI-TRAILER}}
== Monter le Sense Hat ==
'''1.''' If you have not yet installed the Sense HAT, now is the time to do so. Do this with the Raspberry Pi shut down, disconnected from the mains, and with all other cables disconnected.
'''2.''' The Sense HAT comes in a silver anti-static bag, along with the following fixtures and fittings:<br />Check that these are all present before proceeding.
* 1 x GPIO pin extension header
* 4 x Hexagon stand-offs (female-to-female)
* 8 x M2.5 screws
'''3.''' This diagram shows how it all fits together.
[[Fichier:RASP-SENSE-HAT-ASTRO-PI-10.png]]
'''4.''' First, put the GPIO extension header block onto the Raspberry Pi GPIO pins.
'''5.''' Screw the hexagon stand-offs to the Raspberry Pi itself, by threading the screws through from the bottom and turning the hexagon stand-offs between finger and thumb.
'''6.''' Next, insert the Sense HAT into the GPIO pin extension header. The corner holes should line up with the hexagon stand-offs.
'''7.''' Lastly, put the remaining screws through from the top.
'''8.''' Use a small Phillips screwdriver to tighten each corner stand-off individually. They don't need to be especially tight, just enough to ensure that the HAT doesn't become loose.
== Ensuite ==
Maintenant que nous avons tout assembler et que le Sense HAT est branché sur votre Raspberry-Pi, nous allons avoir besoin de [[RASP-SENSE-HAT-ASTRO-PI-Logiciel|procéder à l'installation du logiciel]].
{{RASP-SENSE-HAT-ASTRO-PI-TRAILER}}