29 918
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Page créée avec « {{ADAFRUIT-FONA-NAV}} == Assembler == {{asm-begin}} {{asm-row|img=ADAFRUIT-FONA-Asm-10.jpg}} {{asm-text}} '''Prepare the header strip:'''<br /> Cut the strip to length i... »
{{ADAFRUIT-FONA-NAV}}
== Assembler ==
{{asm-begin}}
{{asm-row|img=ADAFRUIT-FONA-Asm-10.jpg}}
{{asm-text}} '''Prepare the header strip:'''<br />
Cut the strip to length if necessary. It will be easier to solder if you insert it into a breadboard - long pins down.
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} '''Add the breakout board::'''<br />
Place the breakout board over the pins so that the short pins poke through the breakout pads
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} '''And Solder!'''<br />
Be sure to solder all pins for reliable electrical contact.
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} You're done! Check your solder joints visually and continue onto the next steps
{{asm-end}}
== Brancher une antenne ==
A battery and antenna is required! If you have a uFL FONA, a uFL->SMA cable may be required to connect the antenna. Use any Lipoly or LiIon 3.7V/4.2V battery
{{ADFImage|ADAFRUIT-FONA-Asm-20.jpg|640px}}
Check polarity for the battery!'''<br />
Snap the µFL connector on, it will click when placed properly
== SIM Card ==
You must insert a '''SIM card''' to do anything but the most basic tests. FM radio does work without a SIM but of course you cannot send or receive texts, calls, etc!
{{asm-begin}}
{{asm-row|img=ADAFRUIT-FONA-Asm-30.jpg}}
{{asm-text}} The SIM card holder is on the back. It holds a very-standard "Mini SIM"<br />
Micro SIMs will not work! Make sure you get a "Mini SIM"
{{asm-row|img=ADAFRUIT-FONA-Asm-31.jpg}}
{{asm-text}} Open by sliding the cover towards the antenna
{{asm-row|img=ADAFRUIT-FONA-Asm-32.jpg}}
{{asm-text}} Insert the SIM with the gold pads facing up and the notch on the outer corner
{{asm-row|img=ADAFRUIT-FONA-Asm-33.jpg}}
{{asm-text}} Close the hinge down and slide the cover to lock it in place
{{asm-end}}
{{ADAFRUIT-FONA-TRAILER}}
== Assembler ==
{{asm-begin}}
{{asm-row|img=ADAFRUIT-FONA-Asm-10.jpg}}
{{asm-text}} '''Prepare the header strip:'''<br />
Cut the strip to length if necessary. It will be easier to solder if you insert it into a breadboard - long pins down.
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} '''Add the breakout board::'''<br />
Place the breakout board over the pins so that the short pins poke through the breakout pads
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} '''And Solder!'''<br />
Be sure to solder all pins for reliable electrical contact.
{{asm-row|img=ADAFRUIT-FONA-Asm-11.jpg}}
{{asm-text}} You're done! Check your solder joints visually and continue onto the next steps
{{asm-end}}
== Brancher une antenne ==
A battery and antenna is required! If you have a uFL FONA, a uFL->SMA cable may be required to connect the antenna. Use any Lipoly or LiIon 3.7V/4.2V battery
{{ADFImage|ADAFRUIT-FONA-Asm-20.jpg|640px}}
Check polarity for the battery!'''<br />
Snap the µFL connector on, it will click when placed properly
== SIM Card ==
You must insert a '''SIM card''' to do anything but the most basic tests. FM radio does work without a SIM but of course you cannot send or receive texts, calls, etc!
{{asm-begin}}
{{asm-row|img=ADAFRUIT-FONA-Asm-30.jpg}}
{{asm-text}} The SIM card holder is on the back. It holds a very-standard "Mini SIM"<br />
Micro SIMs will not work! Make sure you get a "Mini SIM"
{{asm-row|img=ADAFRUIT-FONA-Asm-31.jpg}}
{{asm-text}} Open by sliding the cover towards the antenna
{{asm-row|img=ADAFRUIT-FONA-Asm-32.jpg}}
{{asm-text}} Insert the SIM with the gold pads facing up and the notch on the outer corner
{{asm-row|img=ADAFRUIT-FONA-Asm-33.jpg}}
{{asm-text}} Close the hinge down and slide the cover to lock it in place
{{asm-end}}
{{ADAFRUIT-FONA-TRAILER}}