Ligne 74 : |
Ligne 74 : |
| {{traduction}} | | {{traduction}} |
| | | |
− | La carte motor-skin est fournie avec une rangée de connecteur standard (pin Header). Vous pouvez cependant opter pour des {{pl|948|stacking header pour PyBoard}}.
| + | The motor-skin board is provided with a pinHeader section. You can also use a {{pl|948|stacking header for PyBoard}}. |
| | | |
− | Le stacking header vous permettra de brancher autres cartes (fils ou composants) sur votre PyBoard.
| + | The stacking header would allows to stack board over the motor skin (or wiring your own components) to contrôle them with your pyboard. |
| | | |
− | Nous allons vous montrer comment brancher les deux types de connecteurs sur le Motor-Skin
| + | We will show how to assemble the two types of connectors on the Motor-Skin |
| | | |
| {{asm-begin}} | | {{asm-begin}} |
| | | |
| {{asm-row|img=capt0015.jpg}} | | {{asm-row|img=capt0015.jpg}} |
− | {{asm-text}} Voila, c'est le moment de choisir entre les connecteurs standards (pin Header) fournis dans le kit | + | {{asm-text}} It is now time to choose the connector type: |
| | | |
− | '''OU'''
| + | You can select the connector included within the kit |
| | | |
− | d'opter pour des {{pl|948|stacking header pour PyBoard}}.
| + | '''OR''' |
| + | |
| + | buy a set of {{pl|948|stacking header for PyBoard}}. |
| | | |
| {{asm-row|img=capt0016.jpg}} | | {{asm-row|img=capt0016.jpg}} |
− | {{asm-text}} {{underline|'''Pour les connecteurs standards:'''}} | + | {{asm-text}} {{underline|'''Using the standard pinHeader:'''}} |
| | | |
− | Placer la rangée de connecteur sur la pyboard et couper à longueur.
| + | Place the section of pinHeader in the PyBoard connector and cut them to the appropriate length. |
| | | |
| {{asm-row|img=capt0017.jpg}} | | {{asm-row|img=capt0017.jpg}} |
− | {{asm-text}} Répétez l'opération 3 fois de façon a couvrir les 3 côtés de la pyboard. | + | {{asm-text}} Repeat the operation to conver the 3 sides of the PyBoard. |
| | | |
− | Soit 2 rangées de 16 broches et une rangée de 10 broches.
| + | You should have 2 sections of 16 pins + 1 section of 10 pins. |
| | | |
| {{asm-row|img=capt0019.jpg}} | | {{asm-row|img=capt0019.jpg}} |
− | {{asm-text}} Placer ensuite la carte motor-skin sur les broches placées dans les connecteurs de la PyBoard. | + | {{asm-text}} Place the motor-skin board over the pin-header. |
| | | |
− | La têtes des connecteurs doit dépasser de l'autre côté de la carte Motor-Skin.
| + | The pinHeader's head should be visible through the holes of the Motor-Skin board. |
| | | |
| {{asm-row|img=capt0020.jpg}} | | {{asm-row|img=capt0020.jpg}} |
− | {{asm-text}} Il ne reste plus qu'à souder toutes les broches sur le motor-skin | + | {{asm-text}} It is now time to use the iron to soler each of the pins on the motor-skin |
| | | |
| {{asm-row|img=capt0021.jpg}} | | {{asm-row|img=capt0021.jpg}} |
− | {{asm-text}} {{underline|'''Pour les connecteurs stacking header:'''}} | + | {{asm-text}} {{underline|'''Using the stacking header:'''}} |
| | | |
− | Placez tous les connecteurs du kit "{{pl|948|stacking header}}".
| + | Place all the sections of the kit "{{pl|948|stacking header}}" on the motor-skin board. |
| | | |
− | Il est tout a fait normal que la partie PVC du connecteur reste sur-élevée de carte.
| + | The plastic part of the connector should not go down to the board. They should stays a bit "higher" (as on the picture). |
| | | |
| {{asm-row|img=capt0022.jpg}} | | {{asm-row|img=capt0022.jpg}} |
− | {{asm-text}} Enficher ensuite ces connecteurs sur la carte PyBoard pour qu'ils soient tous correctement alignés (au moment où ils seront soudés). | + | {{asm-text}} Then, it is very important to insert the motor-skin+connector on the PyBoard. This will align all the connectors properly before you starts the soldering phase. |
| | | |
| {{asm-row|img=capt0023.jpg}} | | {{asm-row|img=capt0023.jpg}} |
− | {{asm-text}} Cet image montre l'emplacement des différent connecteurs. | + | {{asm-text}} This picture shows the place for all the connectors. |
| | | |
| {{asm-row|img=capt0024.jpg}} | | {{asm-row|img=capt0024.jpg}} |
− | {{asm-text}} Poser le tout à l'envers sur une surface plane... puis {{underline|souder sommairement}} quelques broches du stacking header sur la carte Motor-Skin. | + | {{asm-text}} Now, upside-down the assembly and lay it down on you desk. Then {{underline|fix some pins with a bit of stain}} (this operation will just fix the pinHeader on the motor-skin in the correct position... this should not be perfect by now). |
| | | |
− | Cela permettra de préserver l'alignement des broches.
| + | This would help to keep the "perfect alignment" for further soldering phase. |
| | | |
− | {{ambox-stop|text=Cette opération est un peu délicate. N'hésitez pas à prendre votre temps.}} | + | {{ambox-stop|text=This operation is a bit awkward. Dont hesitate to take your time.}} |
| | | |
| {{asm-row|img=capt0026.jpg}} | | {{asm-row|img=capt0026.jpg}} |
Ligne 140 : |
Ligne 142 : |
| | | |
| {{asm-end}} | | {{asm-end}} |
| + | |
| == Deuxième partie == | | == Deuxième partie == |
| Nous pouvons maintenant poursuivre les opérations d'assemblage. | | Nous pouvons maintenant poursuivre les opérations d'assemblage. |