4 166 octets ajoutés
, 18 mars 2017 à 14:03
{{RASP-FT232H-NAV}}
{{traduction}}
== FT232 en mode SPI ==
The FT232H's MPSSE is great for generating signals to communicate using the SPI protocol. The MPSSE can take care of generating a clock signal from about 450hz to 30Mhz, and read & write bytes of data at that frequency. The Python GPIO library that was installed includes a small wrapper around MPSSE functions to simplify the use of reading and writing SPI data.
When using SPI with the FT232H the following pins will have a special meaning:
* '''D0 - SCK / Clock signal''' : This will be the clock that tells devices when to sample and write data.
* '''D1 - MOSI / Data Out''' : This will output data from the FT232H to the connected device.
* '''D2 - MISO / Data In''' : This will read data from the connected device to the FT232H.
One thing to note is that there isn't an explicit chip select / enable pin. You should use any of the free GPIO pins as a dedicated chip select pin and specify that pin when creating the SPI object.
To use SPI with the Python library you need to create an instance of the Adafruit_GPIO.FT232H.SPI class. For example see the following code:
<syntaxhighlight lang="python">
import Adafruit_GPIO.FT232H as FT232H
# Temporarily disable FTDI serial drivers.
FT232H.use_FT232H()
# Find the first FT232H device.
ft232h = FT232H.FT232H()
# Create a SPI interface from the FT232H using pin 8 (C0) as chip select.
# Use a clock speed of 3mhz, SPI mode 0, and most significant bit first.
spi = FT232H.SPI(ft232h, cs=8, max_speed_hz=3000000, mode=0, bitorder=FT232H.MSBFIRST)
# Write three bytes (0x01, 0x02, 0x03) out using the SPI protocol.
spi.write([0x01, 0x02, 0x03])
</syntaxhighlight>
Notice that the code starts by importing the FT232H part of the GPIO library and disabling the FTDI serial drivers as your saw in the GPIO example.
Next the code creates a FT232H object also like was done in the GPIO example.
The next line of code creates a FT232H.SPI object using the FT232H device that was just created. An optional chip select/slave select line is specified using '''GPIO 8 / pin C0''' with the cs parameter value.
Notice too the speed, mode, and bit order of the SPI protocol are specified as parameters of the initializer. Mode 0 and bit order of ''MSBFIRST'' are actually the default values and do not necessarily need to be specified here, but it's helpful to show them for clarity.
Possible mode values are 0 through 3 and they correspond to [http://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus#Mode_numbers SPI mode values for AVR processors] (''wikipedia, anglais'').
Bitorder can be either '''MSBFIRST''' for most significant bits to be clocked out first, or '''LSBFIRST''' for the least significant bits to be clocked out first.
Finally the last line shows how to send 3 bytes of data out the '''D1 (MOSI)''' line using the '''write()''' function. The '''D0 (SCK)''' line will generate a clock signal, and the '''D1 (MOSI)''' line will clock out bits of data with every clock pulse.
There are also SPI functions you can use to read and transfer (read and write at the same time) data:
<syntaxhighlight lang="python">
# Read 3 bytes of data using the SPI protocol.
response = spi.read(3)
print 'Received {0}'.format(response)
# Write 3 bytes and simultaneously read 3 bytes using the SPI protocl.
response = spi.transfer([0x01, 0x02, 0x03])
print 'Received {0}'.format(response)
</syntaxhighlight>
The '''read()''' function will read the specified number of bytes on the '''D2 (MISO)''' line (sending clock pulses out '''D0 (SCK)''' as necessary).
The '''transfer()''' function is like calling '''write()''' and '''read()''' at the same time. The specified array of bytes will be sent out '''D1 (MOSI)''' while at the same time data will be read from '''D2 (MISO)'''.
That's all there is to using the SPI protocol with the FT232H and the Adafruit Python GPIO library!
You might also be interested in this tutorial which shows how to use the FT232H breakout with some Adafruit SPI devices that have been ported to use Adafruit's Python GPIO library.
== Contrôler des NeoPixels avec SPI ==
{{RASP-FT232H-TRAILER}}