30 072
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Pi-WiringPi-Reference-PiSpecific (voir la source)
Version du 12 octobre 2013 à 15:52
, 12 octobre 2013 à 15:52Page créée avec « {{Pi-WiringPi-NAV}} == Introduction == These functions are not part of the core wiringPi set, but act specifically on the Raspberry Pi hardware itself. Some external hardwar... »
{{Pi-WiringPi-NAV}}
== Introduction ==
These functions are not part of the core wiringPi set, but act specifically on the Raspberry Pi hardware itself. Some external hardware driver modules may provide some of this functionality though.
== Les fonctions ==
=== digitalWriteByte(int value) ===
void digitalWriteByte (int value) ;
This writes the 8-bit byte supplied to the first 8 GPIO pins. It’s the fastest way to set all 8 bits at once to a particular value, although it still takes two write operations to the Pi’s GPIO hardware.
=== pwmSetMode(int mode) ===
pwmSetMode (int mode) ;
The PWM generator can run in 2 modes – “balanced” and “mark:space”. The mark:space mode is traditional, however the default mode in the Pi is “balanced”. You can switch modes by supplying the parameter: PWM_MODE_BAL or PWM_MODE_MS.
=== pwmSetRange(unsigned int range) ===
pwmSetRange(unsigned int range);
This sets the range register in the PWM generator. The default is 1024.
=== pwmSetClock (int divisor) ===
pwmSetClock (int divisor) ;
This sets the divisor for the PWM clock.
Note: The PWM control functions can not be used when in Sys mode. To understand more about the PWM system, you’ll need to read the Broadcom ARM peripherals manual.
=== piBoardRev(void) ===
piBoardRev(void);
This returns the board revision of the Raspberry Pi. It will be either 1 or 2. Some of the BCM_GPIO pins changed number and function when moving from board revision 1 to 2, so if you are using BCM_GPIO pin numbers, then you need to be aware of the differences.
=== wpiPinToGpio(int wPiPin) ===
wpiPinToGpio(int wPiPin);
This returns the BCM_GPIO pin number of the supplied wiringPi pin. It takes the board revision into account.
=== physPinToGpio(int physPin) ===
physPinToGpio(int physPin);
This returns the BCM_GPIO pin number of the supplied physical pin on the P1 connector.
=== setPadDrive(int group, int value) ===
setPadDrive(int group, int value);
This sets the “strength” of the pad drivers for a particular group of pins. There are 3 groups of pins and the drive strength is from 0 to 7. Do not use this unless you know what you are doing.
{{Pi-WiringPi-TRAILER}}
== Introduction ==
These functions are not part of the core wiringPi set, but act specifically on the Raspberry Pi hardware itself. Some external hardware driver modules may provide some of this functionality though.
== Les fonctions ==
=== digitalWriteByte(int value) ===
void digitalWriteByte (int value) ;
This writes the 8-bit byte supplied to the first 8 GPIO pins. It’s the fastest way to set all 8 bits at once to a particular value, although it still takes two write operations to the Pi’s GPIO hardware.
=== pwmSetMode(int mode) ===
pwmSetMode (int mode) ;
The PWM generator can run in 2 modes – “balanced” and “mark:space”. The mark:space mode is traditional, however the default mode in the Pi is “balanced”. You can switch modes by supplying the parameter: PWM_MODE_BAL or PWM_MODE_MS.
=== pwmSetRange(unsigned int range) ===
pwmSetRange(unsigned int range);
This sets the range register in the PWM generator. The default is 1024.
=== pwmSetClock (int divisor) ===
pwmSetClock (int divisor) ;
This sets the divisor for the PWM clock.
Note: The PWM control functions can not be used when in Sys mode. To understand more about the PWM system, you’ll need to read the Broadcom ARM peripherals manual.
=== piBoardRev(void) ===
piBoardRev(void);
This returns the board revision of the Raspberry Pi. It will be either 1 or 2. Some of the BCM_GPIO pins changed number and function when moving from board revision 1 to 2, so if you are using BCM_GPIO pin numbers, then you need to be aware of the differences.
=== wpiPinToGpio(int wPiPin) ===
wpiPinToGpio(int wPiPin);
This returns the BCM_GPIO pin number of the supplied wiringPi pin. It takes the board revision into account.
=== physPinToGpio(int physPin) ===
physPinToGpio(int physPin);
This returns the BCM_GPIO pin number of the supplied physical pin on the P1 connector.
=== setPadDrive(int group, int value) ===
setPadDrive(int group, int value);
This sets the “strength” of the pad drivers for a particular group of pins. There are 3 groups of pins and the drive strength is from 0 to 7. Do not use this unless you know what you are doing.
{{Pi-WiringPi-TRAILER}}