29 836
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Ligne 87 :
Ligne 87 : − ''devrait etre vide, renommer les autres points --1'' − [[Fichier:ADF-ProtoShield-Souder13.jpg]] − − == Etape 14 == Ligne 99 :
Ligne 95 : − + − + − + Ligne 120 :
Ligne 116 : − + Ligne 126 :
Ligne 122 : − + − + Ligne 138 :
Ligne 134 : − == Etape 21 == − devrait etre vide, renommer les autres points --1 − [[Fichier:ADF-ProtoShield-Souder21.jpg]]+ − − − devrait etre vide, renommer les autres points --1 − − [[Fichier:ADF-ProtoShield-Souder22.jpg]] − − == Etape 23 == Ligne 155 :
Ligne 142 : − + Ligne 165 :
Ligne 152 : − Image a changer, voir page [http://www.ladyada.net/make/pshield/solder.html tuto de LadyAda]+ −
aucun résumé de modification
== Etape 13 ==
== Etape 13 ==
[[Fichier:ADF-ProtoShield-Souder14.jpg]]
[[Fichier:ADF-ProtoShield-Souder14.jpg]]
[[Fichier:ADF-ProtoShield-Souder14-02.jpg]]
[[Fichier:ADF-ProtoShield-Souder14-02.jpg]]
== Etape 15 ==
== Etape 14 ==
[[Fichier:ADF-ProtoShield-Souder15.jpg]]
[[Fichier:ADF-ProtoShield-Souder15.jpg]]
If you have a Diecimila (2008), Duemilanove (2009) or newer Arduino, put the long ends of the male header in to the female header on the Arduino, as shown
If you have a Diecimila (2008), Duemilanove (2009) or newer Arduino, put the long ends of the male header in to the female header on the Arduino, as shown
== Etape 16 ==
== Etape 15 ==
[[Fichier:ADF-ProtoShield-Souder16.jpg]]
[[Fichier:ADF-ProtoShield-Souder16.jpg]]
Put the proto shield on top of the Arduino, so that the male header aligns with the solder holes.
Put the proto shield on top of the Arduino, so that the male header aligns with the solder holes.
== Etape 17 ==
== Etape 16 ==
[[Fichier:ADF-ProtoShield-Souder17.jpg]]
[[Fichier:ADF-ProtoShield-Souder17.jpg]]
[[Fichier:ADF-ProtoShield-Souder17-02.jpg]]
[[Fichier:ADF-ProtoShield-Souder17-02.jpg]]
== Etape 18 ==
== Etape 17 ==
<!-- [[Fichier:ADF-ProtoShield-Souder18.jpg]] -->
<!-- [[Fichier:ADF-ProtoShield-Souder18.jpg]] -->
[[Fichier:ADF-ProtoShield-BBoardLarge.jpg]]
[[Fichier:ADF-ProtoShield-BBoardLarge.jpg]]
If you're using a half-sized breadboard you should stop now as adding the remaining parts will make the breadboard not fit as well.
If you're using a half-sized breadboard you should stop now as adding the remaining parts will make the breadboard not fit as well.
== Etape 19 ==
== Etape 18 ==
[[Fichier:ADF-ProtoShield-Souder19.jpg]]
[[Fichier:ADF-ProtoShield-Souder19.jpg]]
Place the two ceramic capacitors. They are symmetric so you don't have to worry about putting them in backwards.
Place the two ceramic capacitors. They are symmetric so you don't have to worry about putting them in backwards.
== Etape 20 ==
== Etape 19 ==
[[Fichier:ADF-ProtoShield-Souder20.jpg]]
[[Fichier:ADF-ProtoShield-Souder20.jpg]]
[[Fichier:ADF-ProtoShield-Souder20-02.jpg]]
[[Fichier:ADF-ProtoShield-Souder20-02.jpg]]
== Etape 20 ==
== Etape 22 ==
[[Fichier:ADF-ProtoShield-Souder23.jpg]]
[[Fichier:ADF-ProtoShield-Souder23.jpg]]
One of the headers is all ground pins, another is all 5V pins. The final one is 'floating', which means you can use a jumper to make it Vin or 3.3V or any other value you need.
One of the headers is all ground pins, another is all 5V pins. The final one is 'floating', which means you can use a jumper to make it Vin or 3.3V or any other value you need.
== Etape 24 ==
== Etape 21 ==
[[Fichier:ADF-ProtoShield-Souder24.jpg]]
[[Fichier:ADF-ProtoShield-Souder24.jpg]]
Source: [http://www.ladyada.net/make/pshield/solder.html tutoriel d'AdaFruit en anglais]
{{ADF-Accord}}
{{ADF-Accord}}
{{MCH-Accord}}
{{MCH-Accord}}