Ligne 2 : |
Ligne 2 : |
| | | |
| {{traduction}} | | {{traduction}} |
| + | |
| + | = Configuration = |
| + | |
| + | Afin d'effectuer plus simplement la première configuration, nous allons éditer directement le fichier de configuration dans votre éditeur de texte habituel directement depuis la carte SD que nous avons créé. |
| + | |
| + | Voici le contenu du fichier par défaut: |
| + | |
| + | <syntaxhighlight lang="python"> |
| + | |
| + | # Uncomment some or all of these to enable the optional hardware interfaces |
| + | # Params: |
| + | # i2c_arm Set to "on" to enable the ARM's i2c interface |
| + | # (default "off") |
| + | # i2c_vc Set to "on" to enable the i2c interface |
| + | # usually reserved for the VideoCore processor |
| + | # (default "off") |
| + | # i2c_arm_baudrate Set the baudrate of the ARM's i2c interface |
| + | # (default "100000") |
| + | # i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface |
| + | # (default "100000") |
| + | # i2c_baudrate An alias for i2c_arm_baudrate |
| + | # i2s Set to "on" to enable the i2s interface |
| + | # (default "off") |
| + | # spi Set to "on" to enable the spi interfaces |
| + | # (default "off") |
| + | # act_led_trigger Choose which activity the LED tracks. |
| + | # Use "heartbeat" for a nice load indicator. |
| + | # (default "mmc") |
| + | # act_led_activelow Set to "on" to invert the sense of the LED |
| + | # (default "off") |
| + | # act_led_gpio Set which GPIO pin to use for the activity LED |
| + | # (in case you want to connect it to an external |
| + | # device) |
| + | # (default "16" on a non-Plus board, "47" on a |
| + | # Plus or Pi 2) |
| + | # N.B. It is recommended to only enable those interfaces that are needed. |
| + | # Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc |
| + | # interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) |
| + | # Note also that i2c, i2c_arm and i2c_vc are aliases for the physical |
| + | # interfaces i2c0 and i2c1. Use of the numeric variants is still possible |
| + | # but deprecated because the ARM/VC assignments differ between board |
| + | # revisions. The same board-specific mapping applies to i2c_baudrate, |
| + | # and the other i2c baudrate parameters. |
| + | |
| + | #dtparam=i2c_arm=on |
| + | #dtparam=i2c_vc=on |
| + | #dtparam=i2s=on |
| + | #dtparam=spi=on |
| + | #dtparam=act_led_trigger=mmc |
| + | |
| + | #dtparam=uart1=off |
| + | dtoverlay=pi3-disable-bt-overlay |
| + | |
| + | # Uncomment one of these lines to enable an audio interface |
| + | #dtoverlay=hifiberry-dac |
| + | #dtoverlay=hifiberry-dacplus |
| + | #dtoverlay=hifiberry-digi |
| + | dtoverlay=hifiberry-amp |
| + | #dtoverlay=iqaudio-dac |
| + | #dtoverlay=iqaudio-dacplus |
| + | |
| + | # Uncomment to enable the lirc-rpi module |
| + | # Params: gpio_out_pin GPIO pin for output (default "17") |
| + | # gpio_in_pin GPIO pin for input (default "18") |
| + | # gpio_in_pull Pull up/down/off on the input pin |
| + | # (default "down") |
| + | # sense Override the IR receive auto-detection logic: |
| + | # "1" = force active high |
| + | # "0" = force active low |
| + | # "-1" = use auto-detection |
| + | # (default "-1") |
| + | # softcarrier Turn the software carrier "on" or "off" |
| + | # (default "on") |
| + | # invert "on" = invert the output pin (default "off") |
| + | # debug "on" = enable additional debug messages |
| + | # (default "off") |
| + | #dtoverlay=lirc-rpi |
| + | #dtparam=gpio_out_pin=17 |
| + | #dtparam=gpio_in_pin=18 |
| + | #dtparam=gpio_in_pull=down |
| + | |
| + | # LCD settings |
| + | # 180 degrees |
| + | lcd_rotate=2 |
| + | # Normal |
| + | #lcd_rotate=0 |
| + | #dtoverlay=rpi-backlight |
| + | #dtoverlay=rpi-ft5406 |
| + | |
| + | # Uncomment if you get no picture on HDMI for a default "safe" mode |
| + | #hdmi_safe=1 |
| + | |
| + | # Uncomment this if your display has a black border of unused pixels visible |
| + | # and your display can output without overscan |
| + | #disable_overscan=1 |
| + | |
| + | # Uncomment the following to adjust overscan. Use positive numbers if console |
| + | # goes off screen, and negative if there is too much border |
| + | #overscan_left=16 |
| + | #overscan_right=16 |
| + | #overscan_top=16 |
| + | #overscan_bottom=16 |
| + | |
| + | # Uncomment to force a console size. By default it will be display's size minus |
| + | # overscan. |
| + | #framebuffer_width=1280 |
| + | #framebuffer_height=720 |
| + | |
| + | # Uncomment if hdmi display is not detected and composite is being output |
| + | #hdmi_force_hotplug=1 |
| + | |
| + | # Uncomment to force a specific HDMI mode (this will force VGA) |
| + | #hdmi_group=1 |
| + | #hdmi_mode=1 |
| + | |
| + | # Uncomment to force a HDMI mode rather than DVI. This can make audio work in |
| + | # DMT (computer monitor) modes |
| + | hdmi_drive=2 |
| + | |
| + | # Uncomment to set monitor mode to DMT |
| + | #hdmi_group=2 |
| + | |
| + | # Uncomment to increase signal to HDMI, if you have interference, blanking, or |
| + | # no display |
| + | #config_hdmi_boost=4 |
| + | |
| + | # setting the max usb current to 1200mA |
| + | max_usb_current=1 |
| + | |
| + | # memory options |
| + | gpu_mem=64 |
| + | |
| + | # Overclocking options |
| + | # force_turbo=1 |
| + | |
| + | |
| + | </syntaxhighlight> |
| + | |
| + | |
| | | |
| = Premier lancement = | | = Premier lancement = |