Ligne 135 : |
Ligne 135 : |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-28.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-28.jpg]] |
| + | |
| + | Solder the regulator in. If you placed the regulator as suggested, you shouldn't have to clip the leads as they'll be short. |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-29.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-29.jpg]] |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-30.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-30.jpg]] |
| + | |
| + | The regulator uses resistors to set the adjustable output voltages. We'll now solder those in. |
| + | |
| + | First is 11.0K '''R3''' (Brown Brown Black Red Brown) - this resistor sets the 3.3V output level. |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-31.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-31.jpg]] |
| + | |
| + | Second is 6.49K '''R5''' (Blue Yellow White Brown Brown) - this resistor is the 'reference' divider for all the voltages |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-32.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-32.jpg]] |
| + | |
| + | Third is 20.5K '''R4''' (Red Black Green Red Brown) - this resistor sets the 5V output voltage |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-33.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-33.jpg]] |
| + | |
| + | Solder and clip the three resistors. |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-34.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-34.jpg]] |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-35.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-35.jpg]] |
| + | |
| + | Now we need a way to select which resistor is connected to the regulator. For that we use a 3-way switch. The switch can only go in one way. |
| + | |
| + | Solder in all the legs of the switch. |
| + | |
| + | Be careful because the solder points are small and somewhat close together. Make sure you don't have a short circuit and that each point is soldered |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-36.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-36.jpg]] |
Ligne 155 : |
Ligne 173 : |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-38.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-38.jpg]] |
| + | |
| + | Now we will put in the capacitors and LEDs for the left hand "low voltage" side. |
| + | First is the red indicator LED. Remember LEDs are polarized. Make sure the long lead goes into the (+) marked pad |
| | | |
| [[Fichier:ADF-ADJ-BBALIM-SOUDER-39.jpg]] | | [[Fichier:ADF-ADJ-BBALIM-SOUDER-39.jpg]] |