Modifications

{{ADFImage|Rasp-PiGRRL-2-Montage2-14.jpg|640px}}

{{ADFImage|Rasp-PiGRRL-2-Montage2-14.jpg|640px}}

== Connected PiTFT and Gamepad ==

<a href="#connected-pitft-and-gamepad" class="anchor-link"><span class="fa fa-link"></span></a><span id="connected-pitft-and-gamepad" class="anchor-link-target"></span>Connected PiTFT and Gamepad</h2>

Now our PiTFT display and Gamepad PCB are mounted to the case. Press the buttons on the PiTFT and Gamepad to test them and see they feel good. If the buttons get stuck, the gamepad isn't flush with the standoffs. 

Now our PiTFT display and Gamepad PCB are mounted to the case. Press the buttons on the PiTFT and Gamepad to test them and see they feel good. If the buttons get stuck, the gamepad isn't flush with the standoffs. 

{{ADFImage|Rasp-PiGRRL-2-Montage2-15.jpg|640px}}

{{ADFImage|Rasp-PiGRRL-2-Montage2-15.jpg|640px}}

== Install Speaker ==

<a href="#install-speaker" class="anchor-link"><span class="fa fa-link"></span></a><span id="install-speaker" class="anchor-link-target"></span>Install Speaker</h2>

Let's go ahead and pop the speaker into the case. Lay the speaker over the cavity with the grill and press it down to snap it into place. The wire should be oriented in a position so it's not in the way of the corner standoff.

Let's go ahead and pop the speaker into the case. Lay the speaker over the cavity with the grill and press it down to snap it into place. The wire should be oriented in a position so it's not in the way of the corner standoff.

{{ADFImage|Rasp-PiGRRL-2-Montage2-25.jpg|640px}}

{{ADFImage|Rasp-PiGRRL-2-Montage2-25.jpg|640px}}

== Install Switch ==

<a href="#install-switch" class="anchor-link"><span class="fa fa-link"></span></a><span id="install-switch" class="anchor-link-target"></span>Install Switch</h2>

Now if a good time to insert the slide switch into the bottom case. Take note of the OFF position of the slide and install it to your liking (I prefer down is OFF, up is ON).

Now if a good time to insert the slide switch into the bottom case. Take note of the OFF position of the slide and install it to your liking (I prefer down is OFF, up is ON).

{{ADFImage|Rasp-PiGRRL-2-Montage2-37.jpg|640px}}

{{ADFImage|Rasp-PiGRRL-2-Montage2-37.jpg|640px}}

== Test PowerBoost Circuit ==

<a href="#test-powerboost-circuit" class="anchor-link"><span class="fa fa-link"></span></a><span id="test-powerboost-circuit" class="anchor-link-target"></span>Test PowerBoost Circuit</h2>

Grab the lipo battery and plug in the JST connector to the JST port on the PowerBoost 1000C. Flip the slide switch on, and see if the circuit works! The blue LED indicates the battery is charged and the circuit is powered on.

Grab the lipo battery and plug in the JST connector to the JST port on the PowerBoost 1000C. Flip the slide switch on, and see if the circuit works! The blue LED indicates the battery is charged and the circuit is powered on.

{{asm-end}}

{{asm-end}}

 

<a href="#almost-done" class="anchor-link"><span class="fa fa-link"></span></a><span id="almost-done" class="anchor-link-target"></span>Almost Done!</h2>

== Almost Done! ==

In the next page, we'll close up the case and finish the build!

In the next page, we'll close up the case and finish the build!

{{Rasp-PiGRRL-2-TRAILER}}

{{Rasp-PiGRRL-2-TRAILER}}