Ligne 52 : |
Ligne 52 : |
| <small>Source: [http://Slic3r.org Slic3r.org]]</small> | | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
− | ==== Taille du lit === | + | ==== Taille du lit ==== |
| This setting defines the maximum distance the extruder may travel along the X and Y axis. If the dimensions are not readily available for the printer then it can be easily measured. | | This setting defines the maximum distance the extruder may travel along the X and Y axis. If the dimensions are not readily available for the printer then it can be easily measured. |
| | | |
Ligne 60 : |
Ligne 60 : |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-03.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-03.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| ==== Taille de la buse ==== | | ==== Taille de la buse ==== |
Ligne 68 : |
Ligne 68 : |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-04.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-04.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| ==== Diamètre du filament ==== | | ==== Diamètre du filament ==== |
Ligne 76 : |
Ligne 76 : |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-05.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-05.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| ==== Température d'extrusion ==== | | ==== Température d'extrusion ==== |
Ligne 86 : |
Ligne 86 : |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-06.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-06.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| ==== Température du lit & fin ==== | | ==== Température du lit & fin ==== |
Ligne 94 : |
Ligne 94 : |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-07.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-07.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| [[Fichier:3D-OrdBot-Slicer-Config-08.png]]<br /> | | [[Fichier:3D-OrdBot-Slicer-Config-08.png]]<br /> |
− | <small>Source: [http://Slic3r.org Slic3r.org]]<small> | + | <small>Source: [http://Slic3r.org Slic3r.org]]</small> |
| | | |
| === Plus d'information === | | === Plus d'information === |