Ligne 33 : |
Ligne 33 : |
| [[Fichier:Plastique-Polymorphe-Make-05.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-05.jpg]] |
| | | |
− | == Travailler le ThermoPlastique == | + | == Conditionner le ThermoPlastique == |
| | | |
| Pour donner forme au plastique, le plus simple est d'utiliser des sous plats en verre bien épais et qui ne crains pas la chaleur ;-). | | Pour donner forme au plastique, le plus simple est d'utiliser des sous plats en verre bien épais et qui ne crains pas la chaleur ;-). |
Ligne 63 : |
Ligne 63 : |
| [[Fichier:Plastique-Polymorphe-Make-10.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-10.jpg]] |
| | | |
− | xx
| + | Au bout de 6 à 12 heures, vous pouvez constater la fin de polymérisation du thermoplastique. |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-11.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-11.jpg]] |
| + | |
| + | C'est le moment de sortie les outils pour travailler la matière :-) |
| + | |
| + | == Travailler le Thermoplastique == |
| + | |
| + | Vous pouvez maintenant sortir votre cutter (ou autres outils) pour commencer à conditionner la feuille de thermoplasique. |
| + | |
| + | Vous pouvez couper toute sortes de formes... mais dans le cas qui nous intéresse, nous avons besoin de bandes aussi large qu'un micro-servo SG90 (soit environ 23mm) |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-12.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-12.jpg]] |
| + | |
| + | Pré-découper partiellement et plier pour obtenir la forme désirée. |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-13.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-13.jpg]] |
| + | |
| + | Et remplissez le creux avec un peu de thermoplastique fondu. |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-14.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-14.jpg]] |
| + | |
| + | Et attendez la polymérisation |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-15.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-15.jpg]] |
| + | |
| + | Recoupez... |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-16.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-16.jpg]] |
| + | |
| + | Re-remplissez le creux avec du thermoplastique fondu. |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-17.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-17.jpg]] |
| + | |
| + | Repositionner comme présenté... et attendez la polymérisation. |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-18.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-18.jpg]] |
| + | |
| + | Ne reste plus qu'a couper à la dimension souhaitée |
| | | |
| [[Fichier:Plastique-Polymorphe-Make-19.jpg]] | | [[Fichier:Plastique-Polymorphe-Make-19.jpg]] |