29 917
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Trinket-Pro-ArduinoIDE-Config (voir la source)
Version du 8 novembre 2014 à 21:52
, 8 novembre 2014 à 21:52Page créée avec « {{Trinket-Pro-NAV}} == Configurer Arduino IDE == {{bloc-etroit|text= Chances are, you picked up a Trinket because it is programmable with the Arduino IDE. The Pro Trinket us... »
{{Trinket-Pro-NAV}}
== Configurer Arduino IDE ==
{{bloc-etroit|text=
Chances are, you picked up a Trinket because it is programmable with the Arduino IDE. The Pro Trinket uses the same core chip as Arduino UNO, and the 5V Pro Trinket uses the same clock rate and voltage so its pretty much a full Arduino-compatible, just smaller!
The only changes you may have to consider when adapting Arduino sketches are:
* Pins #2 and #7 are not available
* The onboard 5V regulator can provide 150mA output, not 800mA out
* You cannot plug shields directly into the Pro Trinket
* There is no Serial-to-USB chip onboard. This is to keep the Pro Trinket small and inexpensive, you can use any FTDI cable to connect to the FTDI port for a Serial connection
* The bootloader on the Pro Trinket use 4KB of FLASH so the maximum sketch size is 28,672 bytes. The bootloader does not affect RAM usage.
{{ambox|text=Even though Trinket has a USB connector, it does not have a "Serial Console" capability, so you cannot use Serial to send and receive data to/from a computer without a seperate FTDI Cable!}}
}}
== La méthode rapide ==
If you don't want to modify an existing Arduino IDE install, you can simply download our ready-to-go and tested Flora/Gemma/Trinket-ified v1.05 right here:
{{ambox-stop|text=Be sure to extract the contents of the zip file. The IDE will not execute properly from a compressed folder.}}
=== Mac OSX ===
xxx
=== Linux ===
== La méthode lente ==
Le Trinket Pro n'est pas supporté nativement par Arduino IDE mais
{{Trinket-Pro-TRAILER}}
== Configurer Arduino IDE ==
{{bloc-etroit|text=
Chances are, you picked up a Trinket because it is programmable with the Arduino IDE. The Pro Trinket uses the same core chip as Arduino UNO, and the 5V Pro Trinket uses the same clock rate and voltage so its pretty much a full Arduino-compatible, just smaller!
The only changes you may have to consider when adapting Arduino sketches are:
* Pins #2 and #7 are not available
* The onboard 5V regulator can provide 150mA output, not 800mA out
* You cannot plug shields directly into the Pro Trinket
* There is no Serial-to-USB chip onboard. This is to keep the Pro Trinket small and inexpensive, you can use any FTDI cable to connect to the FTDI port for a Serial connection
* The bootloader on the Pro Trinket use 4KB of FLASH so the maximum sketch size is 28,672 bytes. The bootloader does not affect RAM usage.
{{ambox|text=Even though Trinket has a USB connector, it does not have a "Serial Console" capability, so you cannot use Serial to send and receive data to/from a computer without a seperate FTDI Cable!}}
}}
== La méthode rapide ==
If you don't want to modify an existing Arduino IDE install, you can simply download our ready-to-go and tested Flora/Gemma/Trinket-ified v1.05 right here:
{{ambox-stop|text=Be sure to extract the contents of the zip file. The IDE will not execute properly from a compressed folder.}}
=== Mac OSX ===
xxx
=== Linux ===
== La méthode lente ==
Le Trinket Pro n'est pas supporté nativement par Arduino IDE mais
{{Trinket-Pro-TRAILER}}