Différences entre versions de « Piles et accus pour alimenter des Pixels-Diode »
| Ligne 14 : | Ligne 14 : | ||
== Montage == | == Montage == | ||
| − | + | <small>Crédit à [http://www.adafruit.com Adafruit] pour toutes les images ci-dessous.<br />Credit [http://www.adafruit.com Adafruit] for all the pictures here under</small> | |
{{asm-begin}} | {{asm-begin}} | ||
Version du 16 août 2014 à 14:33
Utiliser une Diode
Crédit: AdaFruit Industries www.adafruit.com
A single 1N4001 diode has about a 0.7 Volt drop across its leads. Wired to our 6 Volt battery pack (when using alkaline cells), this yields 5.3 Volts output. That’s within our 5V±10% target window, so this simple component addition is all that’s needed to use the battery pack with the LED strips and pixels.
This same solution can be seen in our Digital Programmable LED Belt Kit.
Diodes have a specific polarity, passing current in only one direction…the silver stripe is the + end. So we want to connect the + terminal from the battery pack to the “dark” end with no stripe.
 |
This sequence is only needed if you’ll be using alkaline cells. If you know for a FACT that ONLY rechargeables will be used, this part can be skipped. If you’re unsure, or will use different cells at different times, add the diode. |
Montage
Crédit à Adafruit pour toutes les images ci-dessous.
Credit Adafruit for all the pictures here under
|
Cut the rouge wire of the battery pack short by about an inch. |
|
Strip off about 3/8" insulation from the red wire. |
|
Then “tin” the end of the wire with a bit of solder to keep it from fraying. |
|
Clip the end of the diode (the “dark” end, without a silver stripe) to a similar length, then solder the red wire to this. |
|
Clip the other end of the diode (the side with a silver stripe). |
|
Cut off and slide a 2" piece of heat shrink tube onto the red wire. Keep sliding it all the way past the diode. |
|
Now solder the positive wire from your LED circuit to the “stripe” end of the diode. Or you can add a plug/receptacle pair between the two to make them easier to separate and service later on. |
|
Take the piece of heat shrink you slid over the wire before… |
|
…and slide it back over the diode and the solder joints. |
|
Shrink the tubing to grip the diode and wires. You can use a heat gun, lighter or the edge of your soldering iron. |
|
Taa-daah! |
The black wire from the battery holder then connects to the ground wire of the LED circuit (or plug/receptacle, if you’ve installed one). This side is much simpler than the diode-equipped wire:
|
Slide a small 1" piece of heat shrink onto the black wire (this image shows a much shorter piece…oops…go a little longer than this). |
|
Solder together the ends of the wires. The dreaded inline splice! |
|
Then slide and shrink as you did before. Done! |
Source: Battery Power for LED Pixels ans Strips créé par Phillip Burgess pour AdaFruit Industries. Crédit AdaFruit Industries
Traduit par Meurisse D. pour MCHobby.be
Traduit avec l'autorisation d'AdaFruit Industries - Translated with the permission from Adafruit Industries - www.adafruit.com
Toute référence, mention ou extrait de cette traduction doit être explicitement accompagné du texte suivant : « Traduction par MCHobby (www.MCHobby.be) - Vente de kit et composants » avec un lien vers la source (donc cette page) et ce quelque soit le média utilisé.
L'utilisation commercial de la traduction (texte) et/ou réalisation, même partielle, pourrait être soumis à redevance. Dans tous les cas de figures, vous devez également obtenir l'accord du(des) détenteur initial des droits. Celui de MC Hobby s'arrêtant au travail de traduction proprement dit.