RASP-HAT-TV

De MCHobby - Wiki
Aller à : navigation, rechercher

MCHobby investit du temps et de l'argent dans la réalisation de traduction et/ou documentation. C'est un travail long et fastidieux réalisé dans l'esprit Open-Source... donc gratuit et librement accessible.
SI vous aimez nos traductions et documentations ALORS aidez nous à en produire plus en achetant vos produits chez MCHobby.

Introduction

RASP-HAT-TV-00.jpg

The TV HAT allows you to receive and decode digital television streams on your Raspberry Pi through its on-board DVB-T2 tuner. Then you can watch these streams on any computer connected to the same network as the Pi.

The software we recommend to decode the streams (known as multiplexes, or muxes for short) and view content is called TVHeadend, and instructions for setting it up are below. The TV HAT can decode one mux at a time, and each mux can contain several channels to choose from.

Content can either be viewed on the Raspberry Pi to which the TV-HAT is connected, or sent to another device on the same network.

You will need:

  • A TV aerial
  • A Raspberry Pi TV HAT with its stand-offs, screws, and aerial adaptor
  • A Raspberry Pi that is connected to the internet (plus a mouse, keyboard, and display, if you are not accessing it remotely)
  • Another computer connected to the same network

A propos de cette traduction

Ce document est une traduction libre de la documentation officiel (pdf) proposé par la fondation Raspberry-Pi.

Cette traduction est réalisée par MC Hobby.

Instructions d'installation

Sur votre Raspberry-Pi

  • Connect the aerial adaptor to the TV HAT. With the adaptor pointing away from the USB ports, press the HAT gently down over the Raspberry Pi’s GPIO pins. Place the spacers at two or three of the corners of the HAT, and tighten the screws through the mounting holes to hold them in place.
  • Connect the TV HAT’s aerial adaptor to the cable from your TV aerial.
  • Set up the Raspberry Pi with the newest version of the Raspbian operating system, which you can download from​ ​rpf.io/raspbian

    If you don’t know how to do this, follow our guide at rpf.io/startwithpi
  • Start up your Pi, open a terminal window, and run the following two commands to install the TVHeadend software:
sudo apt-get update
sudo apt-get install tvheadend
  • During the TVHeadend installation, you will be asked to choose an administrator account name and password. You’ll need these later, so make sure to pick something you can remember.

Navigateur d'un ordinateur

  • Type the following into the address bar:
    http://raspberrypi.local:9981/extjs.html
  • This should connect to TVHeadend running on the Raspberry Pi.
    • If the address above doesn't work, you’ll need to find out the IP address of the Pi.
      Open a terminal window on your Pi, and run the command hostname -I
    • You’ll see the IP address in two formats: a string of four numbers separated by dots, then a space, then a long string of numbers and letters separated by colons.
    • Copy everything before the space (the four numbers and dots), and paste this into the address bar instead of the raspberrypi.local​ part of the address.
  • Once you have connected to TVHeadend via the browser, you will be prompted to sign in. Use the account name and password you chose when you installed TVHeadend on the Pi.
    A setup wizard should appear.
  • First, set the language you want TVHeadend to use (​ English (GB)​ worked for us; we have not yet tested other languages).
  • Next, set up network, user, and administrator access. If you don’t have specific preferences, leave Allowed network​ blank, and enter an asterisk (​*) in the username​ and password fields. This will let anyone connected to your local network access TVHeadend.
  • You should see a window titled Network settings​. Under Network 2​, you should see Tuner: Sony CDX2880 #0 : DVB-T #0​. For Network type​, choose DVB-T Network​.
  • The next window is Assign predefined muxes to networks​; here, you select the TV stream to receive and decode. Under Network 1​, for Pre-defined muxes​, select your local TV transmitter.
  • When you click Save & Next​, the software will start scanning for the selected mux, and will show a progress bar. After about two minutes, you should see something like:
Found muxes: 8
Found services: 172
  • In the next window, titled ​ Service mapping​ , tick all three boxes: Map all services​ , Create provider tags​, and Create network tags​.
  • Next you should see a list of TV channels you can watch, along with the programmes they’re currently showing.
  • To watch a TV channel in the browser, click the little TV icon to the left of the channel listing, just to the right of the i icon. This brings up an in-browser media player.
  • To watch a TV channel in a local media player, e.g. VLC (​www.videolan.org/vlc​), you’ll need to download it: click the i icon to the left of a channel listing to bring up the information panel for that channel. Here you can see a stream file that you can download.

TVHeadend is supported by numerous apps, such as TvhClient​ for iOS, which will play TV from the Pi. ​Kodi​ and ​OMXPlayer​ are also supported for viewing TV streams.

To discuss other features or uses, please visit rpf.io/forums​.

Où acheter


Tutoriel créé par Meurisse D. pour MC Hobby SPRL.

Toute référence, mention ou extrait de cette traduction doit être explicitement accompagné du texte suivant : «  Traduction par MCHobby (www.MCHobby.be) - Vente de kit et composants » avec un lien vers la source (donc cette page) et ce quelque soit le média utilisé.

L'utilisation commercial de la traduction (texte) et/ou réalisation, même partielle, pourrait être soumis à redevance. Dans tous les cas de figures, vous devez également obtenir l'accord du(des) détenteur initial des droits. Celui de MC Hobby s'arrêtant au travail de traduction proprement dit.