30 894
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Page créée avec « {{EZ-LINK-NAV}} == Intro == {{ADF-Image|EZ-LINK-Programmer-Arduino-01.jpg}} Unlike any other Bluetooth module, you can use the EZ-Link to program an Arduino. The reason thi... »
{{EZ-LINK-NAV}}
== Intro ==
{{ADF-Image|EZ-LINK-Programmer-Arduino-01.jpg}}
Unlike any other Bluetooth module, you can use the EZ-Link to program an Arduino. The reason this is possible is because EZ-Link can dynamically change the baud rate and has the ability to send the DTR signal from the Arduino IDE wirelessly through the module. Both are required if you want to be able to quickly change to the 115.2K signal required for upload and toggle the DTR lines.
{{ambox-stop|text=This techique can be used for Arduino Uno, Duemilanove, Mega and any other ATmega328/168/1280/2560 based Arduinos that use a USB->Serial converter. It won't work with "USB" Arduinos such as the Leonardo/Micro/Flora since they need a direct USB connection}}
This technique has been tested on Mac OS X and Windows 7, but should work identically on any other OS.
You can use any version of the Arduino IDE with this technique, the Bluetooth part is completely transparent to the software
== Avant de commencer ==
You will need to first be paired to the module, and ideally go through the loopback test so you know that's all working!
== Branchement ==
Wire up the EZ-Link to the Arduino as follows, we'll be using an Uno but the wiring is the same for another kind of Arduino/Compatible.
Connect:
* EZ-Link '''GND''' to Arduino '''GND'''
* EZ-Link '''DSR''' to '''GND''' (or no connect)
* EZ-Link '''Vin''' to Arduino '''5V''' (or any other 3-16V power input, 5V is ideal)
* EZ-Link '''TX''' to Arduino '''#0''' (RX)
* EZ-Link '''RX''' to Arduino '''#1''' (TX)
* EZ-Link '''DTR''' to a 1µF capacitor in series with Arduino '''Reset''' (The cap is in series, so Reset goes to the capacitor +, and capacitor - goes to DTR)
{{ADF-Image|EZ-LINK-Programmer-Arduino-10.jpg}}
If you're using an Arduino compatible such as a Mini or Boarduino (or any of the other hundreds of Arduino-compat's), chances are it has an FTDI connector on it. You can plug the EZ-Link directly in, the '''GND''' pin lines up with the '''Black''' wire, and the '''DTR''' pin lines up with the '''Green''' wire. No other components are required
{{ADF-Image|EZ-LINK-Programmer-Arduino-11.jpg}}
== Upload ==
That's it! Now you can open up the Arduino IDE and select the COM/Serial port that you identified as the EZ-Link. If you open and close the Serial Monitor you should see the Arduino reset (the L pin #13 LED will blink)
[http://forum.arduino.cc/index.php/topic,46977.0.html If you're using Windows, the Arduino IDE might be a little sluggish while selecting the Bluetooth COM port, this is due to a bug in the underlying Java RX/TX library. You can fix it by following the instructions in this Arduino forum post]
{{ambox-stop|text=Since opening and closing a bluetooth connection takes a few seconds, there will be an extra 10 second delay when starting the upload process. This is due to the Bluetooth wireless protocol and how the Arduino IDE opens and closes the connection a few times to reset the Arduino. Please be patient!}}
{{EZ-LINK-TRAILER}}
== Intro ==
{{ADF-Image|EZ-LINK-Programmer-Arduino-01.jpg}}
Unlike any other Bluetooth module, you can use the EZ-Link to program an Arduino. The reason this is possible is because EZ-Link can dynamically change the baud rate and has the ability to send the DTR signal from the Arduino IDE wirelessly through the module. Both are required if you want to be able to quickly change to the 115.2K signal required for upload and toggle the DTR lines.
{{ambox-stop|text=This techique can be used for Arduino Uno, Duemilanove, Mega and any other ATmega328/168/1280/2560 based Arduinos that use a USB->Serial converter. It won't work with "USB" Arduinos such as the Leonardo/Micro/Flora since they need a direct USB connection}}
This technique has been tested on Mac OS X and Windows 7, but should work identically on any other OS.
You can use any version of the Arduino IDE with this technique, the Bluetooth part is completely transparent to the software
== Avant de commencer ==
You will need to first be paired to the module, and ideally go through the loopback test so you know that's all working!
== Branchement ==
Wire up the EZ-Link to the Arduino as follows, we'll be using an Uno but the wiring is the same for another kind of Arduino/Compatible.
Connect:
* EZ-Link '''GND''' to Arduino '''GND'''
* EZ-Link '''DSR''' to '''GND''' (or no connect)
* EZ-Link '''Vin''' to Arduino '''5V''' (or any other 3-16V power input, 5V is ideal)
* EZ-Link '''TX''' to Arduino '''#0''' (RX)
* EZ-Link '''RX''' to Arduino '''#1''' (TX)
* EZ-Link '''DTR''' to a 1µF capacitor in series with Arduino '''Reset''' (The cap is in series, so Reset goes to the capacitor +, and capacitor - goes to DTR)
{{ADF-Image|EZ-LINK-Programmer-Arduino-10.jpg}}
If you're using an Arduino compatible such as a Mini or Boarduino (or any of the other hundreds of Arduino-compat's), chances are it has an FTDI connector on it. You can plug the EZ-Link directly in, the '''GND''' pin lines up with the '''Black''' wire, and the '''DTR''' pin lines up with the '''Green''' wire. No other components are required
{{ADF-Image|EZ-LINK-Programmer-Arduino-11.jpg}}
== Upload ==
That's it! Now you can open up the Arduino IDE and select the COM/Serial port that you identified as the EZ-Link. If you open and close the Serial Monitor you should see the Arduino reset (the L pin #13 LED will blink)
[http://forum.arduino.cc/index.php/topic,46977.0.html If you're using Windows, the Arduino IDE might be a little sluggish while selecting the Bluetooth COM port, this is due to a bug in the underlying Java RX/TX library. You can fix it by following the instructions in this Arduino forum post]
{{ambox-stop|text=Since opening and closing a bluetooth connection takes a few seconds, there will be an extra 10 second delay when starting the upload process. This is due to the Bluetooth wireless protocol and how the Arduino IDE opens and closes the connection a few times to reset the Arduino. Please be patient!}}
{{EZ-LINK-TRAILER}}