Modifications

Sauter à la navigation Sauter à la recherche

Senseur IR Decodeur IR (voir la source)

Version du 30 juillet 2012 à 11:21

8 610 octets ajoutés ,  30 juillet 2012 à 11:21
→‎xxx
Ligne 1 : Ligne 1 :  
{{SenseurIR-Nav}}
 
{{SenseurIR-Nav}}
   −
== xxx ==
+
For our final project, we will use a remote control to send messages to a microcontroller. For example, this might be useful for a robot that can be directed with an IR remote. It can also be good for projects that you want to control from far away, without wires.
−
xxx
      +
For a remote in this example we'll be using an Apple clicker remote. You can use any kind of remote you wish, or you can steal one of these from an unsuspecting hipster.
 +
 +
[[Fichier:IR-appleremote.jpeg]]
 +
 +
We'll use the code from our previous sketch for raw IR reading but this time we'll edit our printer-outer to have it give us the pulses in a C array, this will make it easier for us to use for pattern matching.
 +
 +
<nowiki>
 +
    void printpulses(void) {
 +
    Serial.println("\n\r\n\rReceived: \n\rOFF \tON");
 +
    for (uint8_t i = 0; i < currentpulse; i++) {
 +
    Serial.print(pulses[i][0] * RESOLUTION, DEC);
 +
    Serial.print(" usec, ");
 +
    Serial.print(pulses[i][1] * RESOLUTION, DEC);
 +
    Serial.println(" usec");
 +
    }
 +
    // print it in a 'array' format
 +
    Serial.println("int IRsignal[] = {");
 +
    Serial.println("// ON, OFF (in 10's of microseconds)");
 +
    for (uint8_t i = 0; i < currentpulse-1; i++) {
 +
    Serial.print("\t"); // tab
 +
    Serial.print(pulses[i][1] * RESOLUTION / 10, DEC);
 +
    Serial.print(", ");
 +
    Serial.print(pulses[i+1][0] * RESOLUTION / 10, DEC);
 +
    Serial.println(",");
 +
    }
 +
    Serial.print("\t"); // tab
 +
    Serial.print(pulses[currentpulse-1][1] * RESOLUTION / 10, DEC);
 +
    Serial.print(", 0};");
 +
    }
 +
</nowiki>
 +
 +
I uploaded the new sketch and pressed the Play button on the Apple remote and got the following:
 +
 +
<nowiki>
 +
 +
 +
    int IRsignal[] = { // ON, OFF (in 10's of microseconds)
 +
    912, 438,
 +
    68, 48,
 +
    68, 158,
 +
    68, 158,
 +
    68, 158,
 +
    68, 48,
 +
    68, 158,
 +
    68, 158,
 +
    68, 158,
 +
    70, 156,
 +
    70, 158,
 +
    68, 158,
 +
    68, 48,
 +
    68, 46,
 +
    70, 46,
 +
    68, 46,
 +
    68, 160,
 +
    68, 158,
 +
    70, 46,
 +
    68, 158,
 +
    68, 46,
 +
    70, 46,
 +
    68, 48,
 +
    68, 46,
 +
    68, 48,
 +
    66, 48,
 +
    68, 48,
 +
    66, 160,
 +
    66, 50,
 +
    66, 160,
 +
    66, 52,
 +
    64, 160,
 +
    66, 48,
 +
    66, 3950,
 +
    908, 214,
 +
    66, 3012,
 +
    908, 212,
 +
    68, 0};
 +
</nowiki>
 +
 +
We'll try to detect that code. Lets start a new sketch called IR Commander ([http://github.com/adafruit/IR-Commander la version finale du code est disponible sur le GitHub d'AdaFruit]) this will use parts of our previous sketch. The first part we'll do is to create a function that just listens for an IR code an puts the pulse timings into the pulses[] array. It will return the number of pulses it heard as a return-value.
 +
 +
<nowiki>
 +
    int listenForIR(void) {
 +
    currentpulse = 0;
 +
    while (1) {
 +
    uint16_t highpulse, lowpulse; // temporary storage timing
 +
    highpulse = lowpulse = 0; // start out with no pulse length
 +
    // while (digitalRead(IRpin)) { // this is too slow!
 +
    while (IRpin_PIN & (1 << IRpin)) {
 +
    // pin is still HIGH
 +
    // count off another few microseconds
 +
    highpulse++;
 +
    delayMicroseconds(RESOLUTION);
 +
    // If the pulse is too long, we 'timed out' - either nothing
 +
    // was received or the code is finished, so print what
 +
    // we've grabbed so far, and then reset
 +
    if ((highpulse >= MAXPULSE) && (currentpulse != 0)) {
 +
    return currentpulse;
 +
    }
 +
    }
 +
    // we didn't time out so lets stash the reading
 +
    pulses[currentpulse][0] = highpulse;
 +
    // same as above
 +
    while (! (IRpin_PIN & _BV(IRpin))) {
 +
    // pin is still LOW
 +
    lowpulse++;
 +
    delayMicroseconds(RESOLUTION);
 +
    if ((lowpulse >= MAXPULSE) && (currentpulse != 0)) {
 +
    return currentpulse;
 +
    }
 +
    }
 +
    pulses[currentpulse][1] = lowpulse;
 +
    // we read one high-low pulse successfully, continue!
 +
    currentpulse++;
 +
    }
 +
    }
 +
</nowiki>
 +
 +
Our new '''loop()''' will start out just listening for pulses
 +
 +
<nowiki>
 +
    void loop(void) {
 +
    int numberpulses;
 +
    numberpulses = listenForIR();
 +
    Serial.print("Heard ");
 +
    Serial.print(numberpulses);
 +
    Serial.println("-pulse long IR signal");
 +
    }
 +
</nowiki>
 +
 +
When we run this it will print out something like...
 +
 +
[[Fichier:IR-pulsecounter.jpg]]
 +
 +
OK time to make the sketch compare what we received to what we have in our stored array:
 +
 +
[[Fichier:IR-ircompare.jpg]]
 +
 +
As you can see, there is some variation. So when we do our comparison we can't look for preciesely the same values, we have to be a little 'fuzzy'. We'll say that the values can vary by 20% - that should be good enough.
 +
 +
<nowiki>
 +
 +
 +
    // What percent we will allow in variation to match the same code \\ #define FUZZINESS 20
 +
    void loop(void) {
 +
    int numberpulses;
 +
    numberpulses = listenForIR();
 +
    Serial.print("Heard ");
 +
    Serial.print(numberpulses);
 +
    Serial.println("-pulse long IR signal");
 +
    for (int i=0; i< numberpulses-1; i++) {
 +
    int oncode = pulses[i][1] * RESOLUTION / 10;
 +
    int offcode = pulses[i+1][0] * RESOLUTION / 10;
 +
    Serial.print(oncode); // the ON signal we heard
 +
    Serial.print(" - ");
 +
    Serial.print(ApplePlaySignal[i*2 + 0]); // the ON signal we want
 +
    // check to make sure the error is less than FUZZINESS percent
 +
    if ( abs(oncode - ApplePlaySignal[i*2 + 0]) <= (oncode * FUZZINESS / 100)) {
 +
    Serial.print(" (ok)");
 +
    } else {
 +
    Serial.print(" (x)");
 +
    }
 +
    Serial.print(" \t"); // tab
 +
    Serial.print(offcode); // the OFF signal we heard
 +
    Serial.print(" - ");
 +
    Serial.print(ApplePlaySignal[i*2 + 1]); // the OFF signal we want
 +
    if ( abs(offcode - ApplePlaySignal[i*2 + 1]) <= (offcode * FUZZINESS / 100)) {
 +
    Serial.print(" (ok)");
 +
    } else {
 +
    Serial.print(" (x)");
 +
    }
 +
    Serial.println();
 +
    }
 +
    }
 +
</nowiki>
 +
 +
[[Fichier:IR-codecompareok.jpg]]
 +
 +
 +
 +
This loop, as it goes through each pulse, does a little math. It compares the absolute ('''abs()''') difference between the code we heard and the code we're trying to match abs(oncode - ApplePlaySignal[i*2 + 0]) and then makes sure that the error is less than FUZZINESS percent of the code length (oncode * FUZZINESS / 100)
 +
 +
We found we had to tweak the stored values a little to make them match up 100% each time. IR is not a precision-timed protocol so having to make the FUZZINESS 20% or more is not a bad thing
 +
 +
Finally, we can turn the '''loop()''' into its own function which will retunr '''true''' or '''false''' depending on whether it matched the code we ask it to. We also commented out the printing functions
 +
 +
<nowiki>
 +
    boolean IRcompare(int numpulses, int Signal[]) {
 +
    for (int i=0; i< numpulses-1; i++) {
 +
    int oncode = pulses[i][1] * RESOLUTION / 10;
 +
    int offcode = pulses[i+1][0] * RESOLUTION / 10;
 +
    /*
 +
    Serial.print(oncode); // the ON signal we heard
 +
    Serial.print(" - ");
 +
    Serial.print(Signal[i*2 + 0]); // the ON signal we want
 +
    */
 +
    // check to make sure the error is less than FUZZINESS percent
 +
    if ( abs(oncode - Signal[i*2 + 0]) <= (Signal[i*2 + 0] * FUZZINESS / 100)) {
 +
    //Serial.print(" (ok)");
 +
    } else {
 +
    //Serial.print(" (x)");
 +
    // we didn't match perfectly, return a false match
 +
    return false;
 +
    }
 +
    /*
 +
    Serial.print(" \t"); // tab
 +
    Serial.print(offcode); // the OFF signal we heard
 +
    Serial.print(" - ");
 +
    Serial.print(Signal[i*2 + 1]); // the OFF signal we want
 +
    */
 +
    if ( abs(offcode - Signal[i*2 + 1]) <= (Signal[i*2 + 1] * FUZZINESS / 100)) {
 +
    //Serial.print(" (ok)");
 +
    } else {
 +
    //Serial.print(" (x)");
 +
    // we didn't match perfectly, return a false match
 +
    return false;
 +
    }
 +
    //Serial.println();
 +
    }
 +
    // Everything matched!
 +
    return true;
 +
    }
 +
</nowiki>
 +
 +
 +
 +
We then took more IR command data for the 'rewind' and 'fastforward' buttons and put all the code array data into ircodes.h to keep the main sketch from being too long and unreadable ([http://github.com/adafruit/IR-Commander vous pouvez obtenir tout le code depuis le GitHib d'AdaFruit)
 +
 +
Finally, the main loop looks like this:
 +
 +
<nowiki>
 +
    void loop(void) {
 +
    int numberpulses;
 +
    numberpulses = listenForIR();
 +
    Serial.print("Heard ");
 +
    Serial.print(numberpulses);
 +
    Serial.println("-pulse long IR signal");
 +
    if (IRcompare(numberpulses, ApplePlaySignal)) {
 +
    Serial.println("PLAY");
 +
    }
 +
    if (IRcompare(numberpulses, AppleRewindSignal)) {
 +
    Serial.println("REWIND");
 +
    }
 +
    if (IRcompare(numberpulses, AppleForwardSignal)) {
 +
    Serial.println("FORWARD");
 +
    }
 +
    }
 +
</nowiki>
 +
 +
 +
 +
We check against all the codes we know about and print out whenever we get a match. You could now take this code and turn it into something else, like a robot that moves depending on what button is pressed.
 +
 +
After testing, success!
 +
 +
[[Fichier:mulitirbutton.jpg]]
 
{{ADF-Accord}}
 
{{ADF-Accord}}
    
{{MCH-Accord}}
 
{{MCH-Accord}}
Admin
Bureaucrates, Administrateurs
29 910

modifications

Récupérée de « https://wiki.mchobby.be/index.php?title=Spécial:MobileDiff/1696 »

Menu de navigation