29 836
modifications
Modifications
Sauter à la navigation
Sauter à la recherche
Ligne 88 :
Ligne 88 : + + + + Ligne 106 :
Ligne 110 : − + Ligne 126 :
Ligne 130 : − − /* Teensy 3.x w/wing − #define RFM69_RST 9 // "A" − #define RFM69_CS 10 // "B" − #define RFM69_IRQ 4 // "C" − #define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ ) − */ − − /* WICED Feather w/wing − #define RFM69_RST PA4 // "A" − #define RFM69_CS PB4 // "B" − #define RFM69_IRQ PA15 // "C" − #define RFM69_IRQN RFM69_IRQ − */ + + + + − int16_t packetnum = 0; // packet counter, we increment per xmission+ − − − //while (!Serial) { delay(1); } // wait until serial console is open, remove if not tethered to computer Ligne 176 :
Ligne 167 : − + − + − + Ligne 192 :
Ligne 183 : + +
ENG-CANSAT-MISSION1-RECEIVE (voir la source)
Version du 30 octobre 2018 à 18:07
, 30 octobre 2018 à 18:07→The code explained
#include <RH_RF69.h>
#include <RH_RF69.h>
</syntaxhighlight>
</syntaxhighlight>
Then, it defines the parameters for the radio module and the pinout used to wire the RFM69HCW radio module depending on the board used.
The last line create the object {{fname|rf69}} to control the module.
<syntaxhighlight lang="c">
<syntaxhighlight lang="c">
#endif
#endif
#if defined (__AVR_ATmega328P__) // Feather 328P w/wing
#if defined (__AVR_ATmega328P__) // Feather 328P w/wing (or Arduino UNO)
#define RFM69_INT 3 //
#define RFM69_INT 3 //
#define RFM69_CS 4 //
#define RFM69_CS 4 //
#define LED 13
#define LED 13
#endif
#endif
// Singleton instance of the radio driver
// Singleton instance of the radio driver
RH_RF69 rf69(RFM69_CS, RFM69_INT);
RH_RF69 rf69(RFM69_CS, RFM69_INT);
</syntaxhighlight>
</syntaxhighlight>
The {{fname|setup()}} function:
* initialize the serial connexion @ 115200 bauds
* initialze the radio module
<syntaxhighlight lang="c">
<syntaxhighlight lang="c">
void setup() {
void setup()
{
Serial.begin(115200);
Serial.begin(115200);
pinMode(LED, OUTPUT);
pinMode(LED, OUTPUT);
}
}
// If you are using a high power RF69 eg RFM69HW, you *must* set a Tx power with the
// When using High Power RF69, RFM69HW then the Tx power ishighpowermodule
// ishighpowermodule flag set like this:
// flag MUST be with to TRUE
rf69.setTxPower(20, true); // range from 14-20 for power, 2nd arg must be true for 69HCW
rf69.setTxPower(20, true); // Power range 14-20
// The encryption key has to be the same as the one in the server
// The encryption key has to be the same as the one in the server
}
}
</syntaxhighlight>
</syntaxhighlight>
xxxx
<syntaxhighlight lang="c">
<syntaxhighlight lang="c">