Bluefruit-LE-Shield-HIDKeyboard

De MCHobby - Wiki
Sauter à la navigation Sauter à la recherche


MCHobby investit du temps et de l'argent dans la réalisation de traduction et/ou documentation. C'est un travail long et fastidieux réalisé dans l'esprit Open-Source... donc gratuit et librement accessible.
SI vous aimez nos traductions et documentations ALORS aidez nous à en produire plus en achetant vos produits chez MCHobby.
Page-under-construction.pngPage(s) en cours de traduction/élaboration.

Page(s) under translation/construction

Le croquis HIDKeyboard

The HIDKeyboard example shows you how you can use the built-in HID keyboard AT commands to send keyboard data to any BLE-enabled Android or iOS phone, or other device that supports BLE HID peripherals.

Ouvrir le croquis

To open the ATCommand sketch, click on the File > Examples > Adafruit_BluefruitLE_nRF51 folder in the Arduino IDE and select hidkeyboard:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

This will open up a new instance of the example in the IDE, as shown below:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

Configuration

Check the Configuration! page earlier to set up the sketch for Software/Hardware UART or Software/Hardware SPI. The default is hardware SPI

If using software or hardware Serial UART:

  • This tutorial does not need to use the MODE pin, make sure you have the mode switch in CMD mode if you do not configure & connect a MODE pin
  • Don't forget to also connect the CTS pin on the Bluefruit to ground if you are not using it! (The Flora has this already done)

Exécuter le croquis

Once you upload the sketch to your board (via the arrow-shaped upload icon), and the upload process has finished, open up the Serial Monitor via Tools > Serial Monitor, and make sure that the baud rate in the lower right-hand corner is set to 115200:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

Sélection de couleur

You can also send RGB color data via the Color Picker module, which presents the following color selection dialogue:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

This will give you Hexadecimal color data in the following format:

RGB #A42FFF

{{#Widget:Iframe |url=https://youtu.be/Kym6crZF1Pg |width=560 |height=315 |border=0 }}

You can combine the color picker and controller sample sketches to make color-configurable animations triggered by buttons in the mobile app-- very handy for wearables! Download this combined sample code (configured for Feather but easy to adapt to FLORA, BLE Micro, etc.) to get started:

Download-icon.pngfeather_bluefruit_neopixel_animation_controller.zip

Configuration

Check the Configuration! page earlier to set up the sketch for Software/Hardware UART or Software/Hardware SPI. The default is hardware SPI

If using software or hardware Serial UART:

  • This tutorial does not need to use the MODE pin, make sure you have the mode switch in CMD mode if you do not configure & connect a MODE pin
  • Don't forget to also connect the CTS pin on the Bluefruit to ground if you are not using it! (The Flora has this already done)

Exécuter le croquis

Page-under-construction.pngPage(s) en cours de traduction/élaboration.

Page(s) under translation/construction

Once you upload the sketch to your board (via the arrow-shaped upload icon), and the upload process has finished, open up the Serial Monitor via Tools > Serial Monitor, and make sure that the baud rate in the lower right-hand corner is set to 115200:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

To send keyboard data, type anything into the textbox at the top of the Serial Monitor and click the Send button.

Lier le clavier HID

Before you can use the HID keyboard, you will need to 'bond' it to your phone or PC. The bonding process establishes a permanent connection between the two devices, meaning that as soon as your phone or PC sees the Bluefruit LE module again it will automatically connect.

The exact procedures for bonding the keyboard will varying from one platform to another.

Android

To bond the keyboard on a Bluetooth Low Energy enabled Android device, go to the Settings application and click the Bluetooth icon.

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

Inside the Bluetooth setting panel you should see the Bluefruit LE module advertising itself as Bluefruit Keyboard under the 'Available devices' list:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

Tapping the device will start the bonding process, which should end with the Bluefruit Keyboard device being moved to a new 'Paired devices' list with 'Connected' written underneath the device name:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

To delete the bonding information, click the gear icon to the right of the device name and the click the Forget button:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

iOS

To bond the keyboard on an iOS device, go to the Settings application on your phone, and click the Bluetooth menu item.

The keyboard should appear under the OTHER DEVICES list:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

Once the bonding process is complete the device will be moved to the MY DEVICES category, and you can start to use the Bluefruit LE module as a keyboard:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

To unbond the device, click the 'info' icon and then select the Forget this Device option in the menu:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

OS X

To bond the keyboard on an OS X device, go to the Bluetooth Preferences window and click the Pair button beside the Bluefruit Keyboard device generated by this example sketch:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

To unbond the device once it has been paired, click the small 'x' icon beside Bluefruit Keyboard:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com

... and then click the Remove button when the confirmation dialogue box pops up:

{{{2}}}
Crédit: AdaFruit Industries www.adafruit.com


Basé sur "Bluefruit LE Shield" d'Adafruit Industries, écrit par Kevin Townsend - Traduit en Français par shop.mchobby.be CC-BY-SA pour la traduction
Toute copie doit contenir ce crédit, lien vers cette page et la section "crédit de traduction".

Based on "Bluefruit LE Shield" from Adafruit Industries, written by Kevin Townsend - Translated to French by shop.mchobby.be CC-BY-SA for the translation
Copies must includes this credit, link to this page and the section "crédit de traduction" (translation credit).

Traduit avec l'autorisation d'AdaFruit Industries - Translated with the permission from Adafruit Industries - www.adafruit.com