Différences entre versions de « Senseur IR Utiliser »
(→xxx) |
|||
Ligne 1 : | Ligne 1 : | ||
{{SenseurIR-Nav}} | {{SenseurIR-Nav}} | ||
− | The good news is that it is very easy to hook up this sensor. Just connect the output to a digital pin | + | The good news is that it is very easy to hook up this sensor. |
+ | Just connect the output to a digital pin. | ||
− | [[Fichier:IR-Arduino-1.jpg]] | + | The bad news is that the Arduino's friendly digitalRead() procedure |
+ | is a tad too slow to reliably read the fast signal as its coming in. | ||
+ | |||
+ | Thus we use the hardware pin reading function directly from | ||
+ | pin D2, thats what the line "IRpin_PIN & BV(IRpin))" does. | ||
+ | |||
+ | [[Fichier:IR-Arduino-1.jpg|350px]] | ||
[http://github.com/adafruit/Raw-IR-decoder-for-Arduino Vous pouvez obtenir la dernière version du code sur le github d'AdaFruit.] | [http://github.com/adafruit/Raw-IR-decoder-for-Arduino Vous pouvez obtenir la dernière version du code sur le github d'AdaFruit.] | ||
Ligne 111 : | Ligne 118 : | ||
Si vous utilisez ce programme et utilisez une télécommande Sony sur laquelle vous pressez le bouton Marche (On), vous obtiendrez le résultat suivant... | Si vous utilisez ce programme et utilisez une télécommande Sony sur laquelle vous pressez le bouton Marche (On), vous obtiendrez le résultat suivant... | ||
− | [[Fichier:IR-Arduino-2.jpg]] | + | [[Fichier:IR-Arduino-2.jpg|350px]] |
Si vous ignorez la première impulstion OFF (correspond au temps nécessaire au programme Arduino pour s'activer à la première réception du signal InfraRouge) et la dernière impulsion ON (qui est le début du code suivant) vous identifierez le code POWER de Sony: | Si vous ignorez la première impulstion OFF (correspond au temps nécessaire au programme Arduino pour s'activer à la première réception du signal InfraRouge) et la dernière impulsion ON (qui est le début du code suivant) vous identifierez le code POWER de Sony: |
Version du 30 juillet 2012 à 10:57
The good news is that it is very easy to hook up this sensor. Just connect the output to a digital pin.
The bad news is that the Arduino's friendly digitalRead() procedure is a tad too slow to reliably read the fast signal as its coming in.
Thus we use the hardware pin reading function directly from pin D2, thats what the line "IRpin_PIN & BV(IRpin))" does.
Vous pouvez obtenir la dernière version du code sur le github d'AdaFruit.
/* Raw IR decoder sketch! This sketch/program uses the Arduno and a PNA4602 to decode IR received. This can be used to make a IR receiver (by looking for a particular code) or transmitter (by pulsing an IR LED at ~38KHz for the durations detected Code is public domain, check out www.ladyada.net and adafruit.com for more tutorials! */ // We need to use the 'raw' pin reading methods // because timing is very important here and the digitalRead() // procedure is slower! //uint8_t IRpin = 2; // Digital pin #2 is the same as Pin D2 see // http://arduino.cc/en/Hacking/PinMapping168 for the 'raw' pin mapping #define IRpin_PIN PIND #define IRpin 2 // the maximum pulse we'll listen for - 65 milliseconds is a long time #define MAXPULSE 65000 // what our timing resolution should be, larger is better // as its more 'precise' - but too large and you wont get // accurate timing #define RESOLUTION 20 // we will store up to 100 pulse pairs (this is -a lot-) uint16_t pulses[100][2]; // pair is high and low pulse uint8_t currentpulse = 0; // index for pulses we're storing void setup(void) { Serial.begin(9600); Serial.println("Ready to decode IR!"); } void loop(void) { uint16_t highpulse, lowpulse; // temporary storage timing highpulse = lowpulse = 0; // start out with no pulse length // while (digitalRead(IRpin)) { // this is too slow! while (IRpin_PIN & (1 << IRpin)) { // pin is still HIGH // count off another few microseconds highpulse++; delayMicroseconds(RESOLUTION); // If the pulse is too long, we 'timed out' - either nothing // was received or the code is finished, so print what // we've grabbed so far, and then reset if ((highpulse >= MAXPULSE) && (currentpulse != 0)) { printpulses(); currentpulse=0; return; } } // we didn't time out so lets stash the reading pulses[currentpulse][0] = highpulse; // same as above while (! (IRpin_PIN & _BV(IRpin))) { // pin is still LOW lowpulse++; delayMicroseconds(RESOLUTION); if ((lowpulse >= MAXPULSE) && (currentpulse != 0)) { printpulses(); currentpulse=0; return; } } pulses[currentpulse][1] = lowpulse; // we read one high-low pulse successfully, continue! currentpulse++; } void printpulses(void) { Serial.println("\n\r\n\rReceived: \n\rOFF \tON"); for (uint8_t i = 0; i < currentpulse; i++) { Serial.print(pulses[i][0] * RESOLUTION, DEC); Serial.print(" usec, "); Serial.print(pulses[i][1] * RESOLUTION, DEC); Serial.println(" usec"); } // print it in a 'array' format Serial.println("int IRsignal[] = {"); Serial.println("// ON, OFF (in 10's of microseconds)"); for (uint8_t i = 0; i < currentpulse-1; i++) { Serial.print("\t"); // tab Serial.print(pulses[i][1] * RESOLUTION / 10, DEC); Serial.print(", "); Serial.print(pulses[i+1][0] * RESOLUTION / 10, DEC); Serial.println(","); } Serial.print("\t"); // tab Serial.print(pulses[currentpulse-1][1] * RESOLUTION / 10, DEC); Serial.print(", 0};"); }
Si vous utilisez ce programme et utilisez une télécommande Sony sur laquelle vous pressez le bouton Marche (On), vous obtiendrez le résultat suivant...
Si vous ignorez la première impulstion OFF (correspond au temps nécessaire au programme Arduino pour s'activer à la première réception du signal InfraRouge) et la dernière impulsion ON (qui est le début du code suivant) vous identifierez le code POWER de Sony:
PWM ON | OFF |
2.5 ms | 0.6 ms |
1.2 ms | 0.6 ms |
0.6 ms | 0.6 ms |
1.2 ms | 0.6 ms |
0.6 ms | 0.6 ms |
1.2 ms | 0.6 ms |
0.6 ms | 0.6 ms |
0.6 ms | 0.6 ms |
1.2 ms | 0.6 ms |
0.6 ms | 0.6 ms |
0.6 ms | 0.6 ms |
0.6 ms | 0.6 ms |
0.6 ms | 270 ms |
Traduit avec l'autorisation d'AdaFruit Industries - Translated with the permission from Adafruit Industries - www.adafruit.com
Toute référence, mention ou extrait de cette traduction doit être explicitement accompagné du texte suivant : « Traduction par MCHobby (www.MCHobby.be) - Vente de kit et composants » avec un lien vers la source (donc cette page) et ce quelque soit le média utilisé.
L'utilisation commercial de la traduction (texte) et/ou réalisation, même partielle, pourrait être soumis à redevance. Dans tous les cas de figures, vous devez également obtenir l'accord du(des) détenteur initial des droits. Celui de MC Hobby s'arrêtant au travail de traduction proprement dit.