ENG-CANSAT-PICO-RFM69HCW-TEST

De MCHobby - Wiki
Sauter à la navigation Sauter à la recherche

Forewords

It is now time to establish a communication between:

  • a Data Emitter (CanSat) made with a raspberry-Pico + RFM69HCW-433MHz.
  • a Data Receiver (Base Station) made with the second RFM69HCW coupled to another Pico microcontroler.

As the kit contains contains two Pico microcontroller we will be able to create the "Data Emitter" on the CanSat as well as the Data Receiver at the ground station.

In this simple example:

  1. The Data Emitter will send a message and wait 500ms for a response (ACK).
  2. The Data Receiver will receive the message.
  3. The Data Receiver will send a ACK reply.

ENG-CANSAT-PICO-RFM69HCW-TEST-00.jpg

As we will see, there are 2 key items to be highlighted:

  1. The frequency must be identical in the emitter and the receiver (eg: 433.1 MHz in this example).
  2. The encryption key must be identical on the both side.

Installing the RFM69 library

The Adafruit's FRM69HCW are provided with a MicroPython library available on GitHub.

You can download and copy the library manually to your board from the Repository.

Download-icon.pngDownload RFM69 library

First, open the repository, then navigate to the file lib/rfm69.py .

Follow the steps describes in the "BMP280 library installation" to copy the RFM69 library to your micropython board.

Once copied, you can also check the proper installation by typing from rfm69 import * .

The RFM69 library repository contains many examples of usage. Do not hesitate to check them!

About Antennas

For this example, a simple wire twisted in the antenna hole will do a great job for testing.

Please wait before soldering the wire inside the antenna hole!. The antenna hole can be populated with:

The antenna design is a key feature to ensure a reliable communication over a long distance.

A µFl connector (also named uFl) is looking to this:

ENG-CANSAT-RFM69HCW-TEST-uFL-connector.jpg

A PCB SMA Connector is looking to this:

ENG-CANSAT-RFM69HCW-TEST-SMA-connector.jpg

Frequency, Encryption & Power

To make the module communicating together:

  • The module must be identical. You cannot mix them.
  • The tuned frequency must be identical.
  • The encryption key must be identical.

Tuned frequency

The tuned frequency is declared with a line like this:

rfm = RFM69( spi=spi, nss=nss, reset=rst )
rfm.frequency_mhz = 433.1

where the tuned frequency is directly assigned to the frequency_mhz property.

In packet radio, several teams can share the same frequency if they use distinct encryption key.

Like TCP (from TCP/IP network), the packet radio is able to detect packet collision and try to recover from it.

However, more teams share the same frequency, more collision we have.

Encyption Key

The module encrypts the data with AES-128.

The encryption key is defined with 16 bytes and assigned to the encryption_key property.

The code here below defines the key 1234567812345678 under binary format.

...
rfm = RFM69( spi=spi, nss=nss, reset=rst )
rfm.encryption_key = (  b"\x01\x02\x03\x04\x05\x06\x07\x08\x01\x02\x03\x04\x05\x06\x07\x08" )

It is also possible to defines the same key with a more user friendly code.

...
rfm = RFM69( spi=spi, nss=nss, reset=rst )
rfm.encryption_key = bytes( [1,2,3,4,5,6,7,8,1,2,3,4,5,6,7,8] )


When all the teams do use the same frequency and the same key then they will all receives the messages from the other teams also sending messages. Your messages will also been received by all the other teams.

Transmission Power

The transmission power is set with the function call.

The range of power is 14 to 20 (in dBi). Lowest values requires less power. Means higher battery life but also smaller transmission distance.

rf69.setTxPower(20, true);

Notice: the second parameter concerns the HCW radio modules and indicates that extra amplifier is present.



Written by Meurisse D. for MCHobby


MCHobby investit du temps et de l'argent dans la réalisation de traduction et/ou documentation. C'est un travail long et fastidieux réalisé dans l'esprit Open-Source... donc gratuit et librement accessible.
SI vous aimez nos traductions et documentations ALORS aidez nous à en produire plus en achetant vos produits chez MCHobby.