Différences entre versions de « Hack-ENG-MotorSkin-Piece »
Ligne 137 : | Ligne 137 : | ||
{{parts-end}} | {{parts-end}} | ||
− | + | When purchasing a {{pl|918|Motor Skin '''KIT'''}} you will also receive those componants | |
{{parts-begin}} | {{parts-begin}} | ||
{{parts-item | {{parts-item | ||
− | |name= | + | |name=5V Regulatoe |
− | |descr= | + | |descr=Pololu DC-DC 5V S7V7F5 Regulator. Can deliver (500mA) from a source in between 2.7V to 11.8V |
|img=Hack-MotorSkin-Piece-S7V7F5.jpg | |img=Hack-MotorSkin-Piece-S7V7F5.jpg | ||
|link=http://mchobby.be/PrestaShop/product.php?id_product=463 | |link=http://mchobby.be/PrestaShop/product.php?id_product=463 | ||
Ligne 150 : | Ligne 150 : | ||
{{parts-item | {{parts-item | ||
− | |name= | + | |name=Ultrasonic sensor |
− | |descr= | + | |descr=HC-SR04 Ultrasonic Sensor, used to measure a distance between 2cm up to 4m |
|img=Hack-MotorSkin-Piece-HC-SR04.jpg | |img=Hack-MotorSkin-Piece-HC-SR04.jpg | ||
|link=http://mchobby.be/PrestaShop/product.php?id_product=561 | |link=http://mchobby.be/PrestaShop/product.php?id_product=561 |
Version actuelle datée du 6 novembre 2016 à 21:18
Before assembling the kit, we will check the various components.
The Motor Skin BASIC does contains the following items:
Detail | Quantity | |
Motor-Skin board |
The Motor-Skin board disponible ici chez MCHobby |
1 |
330 Ohms Resistor |
Resistor disponible ici chez MCHobby |
1 |
470 Ohms Resistor |
Resistor disponible ici chez MCHobby |
1 |
4.7 KOhms Resistor |
Resistor disponible ici chez MCHobby |
1 |
L293D |
H_Bridge used to control 2 motors (forward & backward). disponible ici chez MCHobby |
1 |
DIP 16 |
Dip support for the L293D chip (so you can easily replace the L293D if you break it) disponible ici chez MCHobby |
1 |
47µF Capacitor |
L293's regulation capacitor disponible ici chez MCHobby |
1 |
Diode Schottky |
Diode balancing back & forward the PyBoard power supply from Pyboard's USB and Motor-skin battery pack. Polarised item, the "-" (minus) is on the same side of silver band. disponible ici chez MCHobby |
1 |
220nF capacitor |
Decoupling capacitor for the motors. Used to eliminate the noise caused by the brush rubbing the motor collector. disponible ici chez MCHobby |
6 |
2.54mm male connector |
Used to connect the motors on the board. disponible ici chez MCHobby |
2 |
Female connector |
A strip of female connector (4 pins) to plug the ultrasonic sensor disponible ici chez MCHobby |
1 |
PinHeader |
Strip of male pinHeader. Used to plug your motor-skin on the PyBoard. You can replace it with a stacking Header disponible ici chez MCHobby |
1 |
Jack Connector |
Power supply connector (centre positive) disponible ici chez MCHobby |
1 |
Screw terminal |
Power supply terminal (screw terminal). Take care about the polarisation. Wiring it upside down would destruct the Motor-Skin. disponible ici chez MCHobby |
1 |
Small BLACK push button |
This tactile switch is used to report the "reset" signal on the motor-skin disponible ici chez MCHobby |
1 |
Small WHITE push button |
4 buttons free of use (to ease user interface creation). disponible ici chez MCHobby |
4 |
When purchasing a Motor Skin KIT you will also receive those componants
Description | Quantité | |
5V Regulatoe |
Pololu DC-DC 5V S7V7F5 Regulator. Can deliver (500mA) from a source in between 2.7V to 11.8V disponible ici chez MCHobby |
1 |
Ultrasonic sensor |
HC-SR04 Ultrasonic Sensor, used to measure a distance between 2cm up to 4m disponible ici chez MCHobby |
1 |
Créé par Meurisse D. pour MCHobby.be - Created by Meurisse D. for MCHobby.be
Every reference, text extract of this document should be accompagned with the following credit text : « produced/translated by MCHobby (www.MCHobby.be) - shop for kit and componants » together with a link to the source (so this page). The credit text must be applied on every type of media.
The commercial usage of this text/translation/project's content may be subject to royality fee. In every use case, you must also have the agreement of the initial owner (concerns translation work and content reuse)