MicroPython-Hack-assembleur
![]() |
En cours de traduction/élaboration. |
introduction
Here you will learn how to write inline assembler in Micro Python.
Note: this is an advanced tutorial, intended for those who already know a bit about microcontrollers and assembly language.
Micro Python includes an inline assembler. It allows you to write assembly routines as a Python function, and you can call them as you would a normal Python function.
Retourner une valeur
Inline assembler functions are denoted by a special function decorator. Let’s start with the simplest example:
@micropython.asm_thumb def fun(): movw(r0, 42)
You can enter this in a script or at the REPL. This function takes no arguments and returns the number 42. r0 is a register, and the value in this register when the function returns is the value that is returned. Micro Python always interprets the r0 as an integer, and converts it to an integer object for the caller.
If you run print(fun()) you will see it print out 42.
Accéder aux périphériques
For something a bit more complicated, let’s turn on an LED:
@micropython.asm_thumb def led_on(): movwt(r0, stm.GPIOA) movw(r1, 1 << 13) strh(r1, [r0, stm.GPIO_BSRRL])
This code uses a few new concepts:
- stm is a module which provides a set of constants for easy access to the registers of the pyboard’s microcontroller. Try running import stm and then help(stm) at the REPL. It will give you a list of all the available constants.
- stm.GPIOA is the address in memory of the GPIOA peripheral. On the pyboard, the red LED is on port A, pin PA13.
- movwt moves a 32-bit number into a register. It is a convenience function that turns into 2 thumb instructions: movw followed by movt. The movt also shifts the immediate value right by 16 bits.
- strh stores a half-word (16 bits). The instruction above stores the lower 16-bits of r1 into the memory location r0 + stm.GPIO_BSRRL. This has the effect of setting high all those pins on port A for which the corresponding bit in r0 is set. In our example above, the 13th bit in r0 is set, so PA13 is pulled high. This turns on the red LED.
Accepter des arguments
Inline assembler functions can accept up to 3 arguments. If they are used, they must be named r0, r1 et r2 to reflect the registers and the calling conventions.
Here is a function that adds its arguments:
@micropython.asm_thumb def asm_add(r0, r1): add(r0, r0, r1)
This performs the computation r0 = r0 + r1. Since the result is put in r0, that is what is returned. Try asm_add(1, 2), it should return 3.
Les boucles
We can assign labels with label(my_label), and branch to them using b(my_label), or a conditional branch like bgt(my_label).
The following example flashes the green LED. It flashes it r0 times.
@micropython.asm_thumb def flash_led(r0): # get the GPIOA address in r1 movwt(r1, stm.GPIOA) # get the bit mask for PA14 (the pin LED #2 is on) movw(r2, 1 << 14) b(loop_entry) label(loop1) # turn LED on strh(r2, [r1, stm.GPIO_BSRRL]) # delay for a bit movwt(r4, 5599900) label(delay_on) sub(r4, r4, 1) cmp(r4, 0) bgt(delay_on) # turn LED off strh(r2, [r1, stm.GPIO_BSRRH]) # delay for a bit movwt(r4, 5599900) label(delay_off) sub(r4, r4, 1) cmp(r4, 0) bgt(delay_off) # loop r0 times sub(r0, r0, 1) label(loop_entry) cmp(r0, 0) bgt(loop1)
Source: Inline assembler écrit par/written by Damien P.George
Traduit par Meurisse D. pour MCHobby.be - Translated by Meurisse D. for MCHobby.be
Traduit avec l'autorisation de micropython.org - Translated with the authorisation of micropython.org
Toute référence, mention ou extrait de cette traduction doit être explicitement accompagné du texte suivant : « Traduction par MCHobby (www.MCHobby.be) - Vente de kit et composants » avec un lien vers la source (donc cette page) et ce quelque soit le média utilisé.
L'utilisation commercial de la traduction (texte) et/ou réalisation, même partielle, pourrait être soumis à redevance. Dans tous les cas de figures, vous devez également obtenir l'accord du(des) détenteur initial des droits. Celui de MC Hobby s'arrêtant au travail de traduction proprement dit.