Différences entre versions de « ENG-CANSAT-SAMPLE »

De MCHobby - Wiki
Sauter à la navigation Sauter à la recherche
 
(3 versions intermédiaires par le même utilisateur non affichées)
Ligne 22 : Ligne 22 :
  
  
[[Fichier:ENG-CANSAT-Pico-Kit-04.png]]
+
[[Fichier:ENG-CANSAT-Pico-Kit-04.png|480px]]
  
  
More details on this [https://arduino103.blogspot.com/2022/11/cansat-creer-des-entretoises-en.html blog post] (_french_)
+
More details on this [https://arduino103.blogspot.com/2022/11/cansat-creer-des-entretoises-en.html '''complete blog post'''] (''french'')
 +
 
 +
== Prototype 2 ==
 +
This second prototype try to creates a multi-level cansat around the [https://shop.mchobby.be/fr/pico-rp2040/2271-kit-cansat-avec-raspberry-pi-pico-micropython-3232100022713.html Pico-Cansat-Kit].
 +
 
 +
[[Fichier:ENG-CANSAT-Pico-Kit-10.png]]
 +
 
 +
This example is based on a more advanced spacer set.
 +
It also explore:
 +
* Openning in the can (eg: for camera).
 +
* Protecting the Lipo (at center of the can).
 +
* Electronic on the top of the can.
 +
 
 +
{{dbox-orange|Surprisingly the PCB material is quite harder to work than aluminium!}}
 +
 
 +
 
 +
[[Fichier:ENG-CANSAT-Pico-Kit-11.png]]
 +
 
 +
More details on this [https://arduino103.blogspot.com/2022/11/cansat-prototype-alu-2-partie-1.html '''complete blog post'''] (''french'')
  
 
== 3D CanSat ==
 
== 3D CanSat ==

Version actuelle datée du 21 novembre 2022 à 17:19

Introduction

The entire project must fit into a can! The size and dimensions are available in CanSat settlement.

This page contains various ressources from MCHobby and contest participants. Such ressources can help you in finding your ways in building your own setup.

Prototype 1

Here the first prototype build around the Pico-Cansat-Kit.

ENG-CANSAT-Pico-Kit-01.jpg

This raw prototype shows how to build Aluminium stand-off from 5mm aluminium section.

Thanks to a Hobby Lathe (Proxxon) and few trick it is possible to build a very strong can.

ENG-CANSAT-Pico-Kit-02.png

Some very common material can be used to create a 0.10mm surrounding wall for the can ;-)

ENG-CANSAT-Pico-Kit-03.png


ENG-CANSAT-Pico-Kit-04.png


More details on this complete blog post (french)

Prototype 2

This second prototype try to creates a multi-level cansat around the Pico-Cansat-Kit.

ENG-CANSAT-Pico-Kit-10.png

This example is based on a more advanced spacer set. It also explore:

  • Openning in the can (eg: for camera).
  • Protecting the Lipo (at center of the can).
  • Electronic on the top of the can.
Surprisingly the PCB material is quite harder to work than aluminium!


ENG-CANSAT-Pico-Kit-11.png

More details on this complete blog post (french)

3D CanSat



Written by Meurisse D. for MCHobby


MCHobby investit du temps et de l'argent dans la réalisation de traduction et/ou documentation. C'est un travail long et fastidieux réalisé dans l'esprit Open-Source... donc gratuit et librement accessible.
SI vous aimez nos traductions et documentations ALORS aidez nous à en produire plus en achetant vos produits chez MCHobby.