Différences entre versions de « ENG-CANSAT-PICO-ASSEMBLY »
Ligne 95 : | Ligne 95 : | ||
== PowerBoost 1000 Charger Soldering == | == PowerBoost 1000 Charger Soldering == | ||
− | The PowerBoost 500 of the kit can be replaced with a PowerBoost 1000 to get more power (1000mA) from the Lipo battery | + | The PowerBoost 500 of the kit can be replaced with a '''PowerBoost 1000 to get more power''' (1000mA) from the Lipo battery |
{{traduction}} | {{traduction}} | ||
+ | |||
+ | {{ambox-stop|text=The instructions doesn't applies to the PowerBoost 500 charger.}} | ||
+ | |||
+ | [[fichier:ENG-CANSAT-PICO-03.jpg|360px]] | ||
+ | |||
+ | Let's solder it | ||
+ | |||
+ | {{asm-begin}} | ||
+ | |||
+ | {{asm-row|img=ENG-CANSAT-PICO-20.jpg}} | ||
+ | {{asm-text}} Pico up the base board with the back of the board on the desk. | ||
+ | |||
+ | You should see Qwiic connector and the text "PowerBoost 500 Charger" written. | ||
+ | |||
+ | {{asm-row|img=ENG-CANSAT-PICO-30.jpg}} | ||
+ | {{asm-text}} Prepare a section of 8 Pins and remove 2 of the pins as showned on the picture. | ||
+ | |||
+ | {{asm-row|img=ENG-CANSAT-PICO-31.jpg}} | ||
+ | {{asm-text}} Place the modified pin Header into the connector (the short part into the connector). | ||
+ | |||
+ | {{underline|Tip:}} use a small piece a paper tape to maintain the connector right in place. | ||
+ | |||
+ | {{asm-row|img=ENG-CANSAT-PICO-22.jpg}} | ||
+ | {{asm-text}} Flip over the board and solder the connector in place. | ||
+ | |||
+ | {{asm-row|img=ENG-CANSAT-PICO-33.jpg}} | ||
+ | {{asm-text}} Flip the board again (to see the "PowerBoost" text). | ||
+ | |||
+ | Slides the PowerBoost 1000 breakout on the connector and Solder the pins (except the 2 missing ones). | ||
+ | |||
+ | '''WARNING: back of the breakout board MUST be visible (not the components)!''' | ||
+ | |||
+ | {{underline|Tip:}} | ||
+ | {{traduction}} | ||
+ | * Push on the PowerBoost breakout with the nail against the connector.<br />This will flatten the breakout on the connector (and make it paralleled to the base board). | ||
+ | * Charge the tip of the iron with some solder. | ||
+ | * Tack a drop of solder a pin to make the breakout staying right in place (no need to be perfect right now) | ||
+ | * Solder the other pins of the breakout | ||
+ | * Now solder the initial tacked pin (to have a nice & great solder join on that pin too) | ||
+ | |||
+ | |||
+ | {{asm-end}} | ||
== RFM69HCW Soldering == | == RFM69HCW Soldering == |
Version du 13 mai 2022 à 21:24
Abstract
This tutorial can be conduct with your own source of materials.
If by any chance you have a Cansat Pico Kit, you do have the needed material but also additional boards to pre-assemble a CANSAT objet.
This section contains recommandations and tips to follow to quickly assemble your kit and be ready to work within 10 to 15 minutes.
Raspberry-Pi Pico Soldering
En cours de traduction/élaboration. |
The Pico is the MicroControler propeling the board.
It is soldered on the top of the Cansat Base Board, this can be done with Pin Header or directly flat on the board.
Lets starts to assemble it!
PowerBoost 500 Charger Soldering
The PowerBoost 500 is the default powering system of this kit.
The instructions doesn't applies to the PowerBoost 1000 charger. |
Let's solder it
PowerBoost 1000 Charger Soldering
The PowerBoost 500 of the kit can be replaced with a PowerBoost 1000 to get more power (1000mA) from the Lipo battery
En cours de traduction/élaboration. |
The instructions doesn't applies to the PowerBoost 500 charger. |
Let's solder it
RFM69HCW Soldering
The RFM69HWC is the radio module used in the CanSat-Pico kit to transmit data
En cours de traduction/élaboration. |
Written by Meurisse D. for MCHobby